Netgear JGSM7224 Support and Manuals
Get Help and Manuals for this Netgear item
View All Support Options Below
Free Netgear JGSM7224 manuals!
Problems with Netgear JGSM7224?
Ask a Question
Free Netgear JGSM7224 manuals!
Problems with Netgear JGSM7224?
Ask a Question
Popular Netgear JGSM7224 Manual Pages
JGSM7224 Hardware Installation Guide - Page 2
... No part of this publication may occur due to the use, or application of NETGEAR, Inc.
Information is subject to the products described in any form or by any liability that may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in this manual, visit the Support website at http://support.netgear...
JGSM7224 Hardware Installation Guide - Page 3
... 10 Installing the Switch 10 Checking the Installation 11 Connecting to Power and Check the LEDs 12 SFP Modules 12 Connecting Equipment to the Switch 13 RJ-45 Ports 13 Connecting a Console to the Switch 13
Chapter 3 Troubleshooting
Troubleshooting Chart 15 Additional Troubleshooting Suggestions 16
Appendix A Default Settings and Technical Specifications
Technical Specifications 17...
JGSM7224 Hardware Installation Guide - Page 4
...; 24-Port Managed Switch JGSM7224. The NETGEAR managed switch is a state-of the switch, see the NETGEAR website at http://www.netgear.com.
Port LEDs
Console Port...copper/fiber combo ports. JGSM7224 Front Panel and LEDs
The following figure shows the front panel of the JGSM7224.
Introduction
1
This guide describes hardware installation and basic troubleshooting for these products, see...
JGSM7224 Hardware Installation Guide - Page 6
... JGSM7224
Safety Instructions
Use...service markings. - The power cable, extension cable, or plug is set...replace the part, or contact your system, purchase a power
Introduction 6 To reduce the risk of the following precautions:
• Observe and follow the operating instructions.
• Keep your system away from radiators and heat sources. Only a trained service technician should service...
JGSM7224 Hardware Installation Guide - Page 8
... items: • Managed Switch with preinstalled software • Power adapter cord • Rubber footpads for tabletop installation • Rubber caps for the SFP sockets • Rack-mounting...Hardware Installation
2
This chapter explains how to the ProSafe JGSM7224 Managed Switch CLI Reference Manual and the ProSafe JGSM7224 Managed Switch Reference Manual. • Installation Guide
...
JGSM7224 Hardware Installation Guide - Page 13
...you to attach devices using either straight-through or crossover cables.
Hardware Installation 13
Note: Ethernet specifications limit the cable length between the switch and the attached device to ...to identify the IP address. You can connect devices, a Gigabit Ethernet module, a console, or a combination of the switch. Connecting a Console to the Switch
After you install the switch and...
JGSM7224 Hardware Installation Guide - Page 14
The following settings: • Baud rate: 9,600 bps • Data bits: 8...setup and configuration (provided as TIP. 4. Describes configuration examples. ProSafe™ 24-Port Managed Switch JGSM7224
2. A link is provided on the Resource CD). • ProSafe JGSM7224 Managed Switch CLI Reference Manual. Configure the terminal-emulation program to configure the switch. Hardware Installation...
JGSM7224 Hardware Installation Guide - Page 15
... or
Half or full duplex setting on the connectors, and make sure that the attached device is set to
performance degradation is properly ...adapter card, cable, or port by testing it in Appendix A. See Technical Specifications in an alternate environment where all products are not the same.
device are functioning. Troubleshooting Chart
Problem Power LED is not working.
problem...
JGSM7224 Hardware Installation Guide - Page 16
... physical aspects of the installation do not resolve your problem, refer to the troubleshooting suggestions in this section.
• Network adapter cards Make sure that the software driver has been installed.
• Configuration If problems occur after you change the network configuration, restore the original connections. If the device does not support auto negotiation, the switch determines...
JGSM7224 Hardware Installation Guide - Page 17
...
Disabled
Gigabit port type
Auto detect
Management IP configuration DHCP, 169.254.100.100/16 will be set if dynamic get failed
User name
Admin
Password
password
Login Authentication Mode Local
Console Login TimeOut
5 minutes
Web access
Enabled for HTTP, Disabled for the ProSafe™ 24-Port Gigabit Managed Switch JGSM7224.
A. Table 1. You can use the RST...
JGSM7224 Hardware Installation Guide - Page 18
...24-Port Managed Switch JGSM7224
Table 1. Default Configuration Settings (Continued)
Features VOICE VLAN Dynamic VLAN (MAC and IP-Subnet based) Spanning Tree Protocol Link aggregation Port mirroring ACL MAC address aging SNMP community ... Enabled Disabled Enabled per JGSM7224 unit but disabled per port Disabled Disabled Disabled Disabled Disabled
Default Settings and Technical Specifications 18
JGSM7224 Hardware Installation Guide - Page 19
...™ 24-Port Managed Switch JGSM7224
Technical Specifications
Table 2. Technical Specifications
Feature IEEE Network Protocol and standards compatibility Switch management
Layer 2 services Layer 3 services
JGSM7224
802.3 10BASE-T 802.3u 100BASE-TX 802.3z 1000BASE-SX 802.3z 1000BASE-LX 802.3ab 1000BASE-T 802.3x flow control
• Port mirroring support • IPv4/IPv6 stack supportt...
JGSM7224 Hardware Installation Guide - Page 20
...Switch JGSM7224
Table 2. Technical Specifications (Continued)
Feature Interface (Auto Uplink on all RJ-45 ports)
Bandwidth 10/100/1000 buffer memory Address database size Mean time between failure (MTBF) Performance Power consumption Dimensions (H x W x D) Environment
Safety
JGSM7224
•... • Altitude: 3,000 m (10,000 ft.) maximum
CB
Default Settings and Technical Specifications 20
JGSM7224 Install Guide - Page 1
... DHCP server is present, the switch assumes a default IP address of 169.254.100.100 and subnet mask of the following the installation instructions included with DHCP server
To perform extensive CLI management, see "Troubleshooting" in this IP value to log into the switch (see "Troubleshooting" in the Hardware Installation Manual for your operating system:
• Windows users can...
JGSM7224 Install Guide - Page 2
..., or in the connected network. Perform steps 1 through its IP address from the serial console port.
1. Type admin for the username and password for selecting NETGEAR products.
c. The IP address used is strongly recommended. See Web Login to the JGSM7224 CLI Reference Manual for product updates, documentation, and support. Registration is configured as a DHCP client to the...
Netgear JGSM7224 Reviews
We have not received any reviews for Netgear yet.