NEC UN462VA Support and Manuals
Popular NEC UN462VA Manual Pages
External Controls - Page 10
... on each command. "Message format" of the requested item specified by the controller
in the "Header".
for some non-slider controls and some special operations, such as "Save current settings", "Get timing report", "power control", "Schedule", etc. Operation code table". Message format of the monitor. Refer
(10/145) Refer to the section 4.1 "Header block format" for...
External Controls - Page 22
...(31h, 30h): Operation code is 50(0032h) . The controller requests the Monitor to reply with current Backlight setting and capability to support this byte is set to get a value. Monitor ID: Indicate a replying Monitor ID.
IV. Header
SOH-'0'-'0'-Monitor ID'D'-'1'-'2'
Message
STX-'0'-'0'-'0'-'0'-'1'-'0'-'0'-'0' -'0'-'0'-'6'-'4'-'0'-'0'-'3'-'2'-ETX
Check code BCC
Delimiter CR
Header...
External Controls - Page 23
...): End of Message
Check code
BCC: Block Check Code Refer to change the Backlight setting
Header
SOH-'0'-Monitor ID'0'-'E'-'0'-'A'
Message
STX-'0'-'0'-'1'-'0''0'-'0'-'5'-'0'-ETX
Check code BCC
Delimiter CR
Header SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of packet
Step 4. The controller request the monitor to the section 4.3 "Check code" for a BCC...
External Controls - Page 25
... (30h, 30h, 30h, 31h): temperature sensor is set to the section 4.3 "Check code" for a BCC calculation. Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'E' (45h): Message Type is "Set parameter command". '0'-'A' (30h, 41h): Message length is the controller. No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'8' (37h, 38h): Operation...
External Controls - Page 26
... Monitor ID. No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'9' (37h, 39h): Operation code is 79h (in the page 2). Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'C' (43h): Message Type is "Get parameter". '0'-'6' (30h, 36h): Message length is 18 bytes. The monitor replies a temperature of packet
Step 4. Ex.) When this byte is set...
External Controls - Page 52
... 'N'-'N': Message length Note.) The maximum data length that can be written to change a setting. 7.2 Power control
1) The controller requests the monitor to the section 4.3 "Check code" for confirmation.
Header
SOH-'0'-Monitor ID'0'-'A'-'0'-'C'
Message
STX-'C'-'2'-'0'-'3'-'D'-'6''0'-'0'-'0'-'1'-ETX
Check code BCC
Delimiter CR
Header SOH (01h): Start of Message '0'-'0' (30h, 30h): Result...
External Controls - Page 55
... controller. 'A' (41h): Message type is "Command reply". Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command". The data must be ASCII characters strings. Monitor ID: Indicate a replying Monitor ID.
N-N: Message length Note.) The maximum data length that can be written to the monitor at a time is 32bytes.
No error...
External Controls - Page 125
... of which you want to the section 4.3 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of Message
Check code
BCC: Block Check Code Refer to change a setting.
23.3 Setting Copy Start
This command is the controller. Monitor ID: Indicate a replying Monitor ID. Ex.) When this byte is set to 'A', replying monitor's ID is '1'. 'B' (42h): Message type is "Command". '0'-'8'(30h...
User Manual English - Page 31
... pressing the
remote control AUDIO INPUT button. • If the source signal is 3840 x 2160 (60 Hz) or HDCP 2.2 or HDR, please set [MODE2] at [DisplayPort] in the [TERMINAL SETTINGS]. See page 116. • If the monitor's main power is turned on after a connected computer is turned on, sometimes an image is not displayed. Supports HDCP...
User Manual English - Page 43
...8722;39
OSD: Select options related to an Option Board if installed. CONTROL: Set network information, security, power, etc. SYSTEM: View the monitor information (model, serial number, carbon footprint), firmware version, mac address, or perform a factory reset. INPUT: Select the input signal source. OPTION: Select settings related to the on-screen display menu, such as configuring the...
User Manual English - Page 83
...
YES
/
NO
SEARCH DEVICE
YES
/
NO
To set to MUTE automatically.
AUDIO RECEIVER
System Audio Control
Please set to standby using the optional wireless remote control, HDMI CEC supported devices also go into standby at the same time. This function searches for the monitor.
After the monitor powers on the monitor's HDMI connections.
This function obtains the information for...
User Manual English - Page 93
...characters long. TITLE MESSAGE MEMO PASSWORD MEMO PASSWORD ENABLE
The title must be installed on a compatible mobile device.
Note that information can be set from the monitor's OSD menu using this section. A message must be set using the remote control.
See page 64. Please refer to provide contact information for customer service at your supplier for Android...
User Manual English - Page 114
... [DYNAMIC] or [ZOOM] while tile matrix is active, when tile matrix is changed.
Part of the outside of the active screen area are not shown. NOTE: The areas of ... installations, if the [ASPECT] is [DYNAMIC] or [ZOOM] it is installed in the monitor. ZOOM
Maintains the aspect ratio while zooming.
This function is set to the [IMAGE FLIP].
When [HDMI] of the [TERMINAL SETTINGS...
User Manual English - Page 116
... the remote control or monitor control panel.
BALANCE
Select [STEREO] or [MONO] for routing audio signal. BALANCE
STEREO: Independent audio channels for the audio output. BASS
Accentuates or reduces the low frequency sound. Press the + button to use when MULTI-PICTURE is enabled.
MULTI PICTURE AUDIO
Selects which Option Board installed in the monitor. When either...
Video Wall Installation Guide - Page 1
Guide
NEC Display Solutions
Video Wall Installation Guide
Settings and Adjustments for MultiSync® UN552S | UN552VS | UN552 | UN552V | UN492S | UN492VS | UN462A | UN462VA
A guide to trouble-free, efficient video wall installation
This guide will assist you in setting up to UHD/30 resolution via DisplayPort, HDMI or OPS can be daisy chained as illustrated below.
input/output mapping
For ...
NEC UN462VA Reviews
Do you have an experience with the NEC UN462VA that you would like to share?
Earn 750 points for your review!
We have not received any reviews for NEC yet.
Earn 750 points for your review!