NEC PX-50VP1A Support and Manuals
Get Help and Manuals for this NEC item
View All Support Options Below
Free NEC PX-50VP1A manuals!
Problems with NEC PX-50VP1A?
Ask a Question
Free NEC PX-50VP1A manuals!
Problems with NEC PX-50VP1A?
Ask a Question
Most Recent NEC PX-50VP1A Questions
What Is Price On New One
i have bran new one in box , what yr did it come out and going price at time
i have bran new one in box , what yr did it come out and going price at time
(Posted by Edsbeamer 4 years ago)
Can I Remove Pip Without A Remote?
I got this tv from a friend but with no remote i hooked up my game system but the pip has the game o...
I got this tv from a friend but with no remote i hooked up my game system but the pip has the game o...
(Posted by miketba70 9 years ago)
Popular NEC PX-50VP1A Manual Pages
42PD2/50PD1 - Page 2
... provide long, trouble-free service. Do not cover rear vents or install in this happens, turn off . NEC is not liable for any part inside . Warnings and Safety Precaution
The NEC plasma monitor is likely to cause harmful interference in which has potentially danger- Therefore, it should be turned off the power to the monitor and unplug the power cord.
Do...
42PD2/50PD1 - Page 3
... it serviced by an authorized NEC Service Center. 5.
Contact NEC Technologies at line voltages greater than 120 Volts AC will gradually decrease over a prolonged period of time, can be susceptible to phosphor burn under certain circumstances. DVI cable (not supplied) band
band Connector
core (small)
core (small)
Power cable (supplied)
core (large)
band
Set side
(Plasma Monitor side...
42PD2/50PD1 - Page 6
...coverage.
HOW YOU CAN GET WARRANTY SERVICE 1. Costs of initial technical adjustments (set forth below , this warranty covers all other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product. 5. Any other cause which proves defective.
Limited Warranty Plasma Monitors
NEC Technologies, Inc. (hereinafter NECTECH) warrants this...
42PD2/50PD1 - Page 7
... ...9 OPTIONS ...9 Setup Procedure ...10 Part Names and Functions Front View ...12 Side View Terminal Board L/R ...13 Remote Controller ...14 Battery Installation and Replacement ...15 Operating Range / Using the wired remote control mode 16 Making the DIP Switch Settings DIP Switch Functions and Settings 17 Power Management Function ...18 Power Management Modes ...18 Installation Wiring Diagram...
42PD2/50PD1 - Page 8
... TEMPORARY USE ONLY AND ARE NOT INTENDED FOR PERMANENT INSTALLATION.
How to Attach Options to the Plasma Monitor
You can attach your optional mounts or stand to the plasma monitor in the diagram to the right. Drawing A
This device cannot be used or installed without a separate Tabletop Stand or other optional mounting accessory. Failure to follow these recommendations could result...
42PD2/50PD1 - Page 9
... registered trademarks of Microsoft Corporation.
The unit can also be used with DMPM (Digital Monitor Power Management) of 3 units can be accommodated Video signals from video cameras, video decks, video disc players, and other video equipment adhering to NTSC as well as a wired remote control (with automatic switching by Windows 98 and Windows 95. (VESA DDC1 and DDC2...
42PD2/50PD1 - Page 10
... supplied remote control cable.
4. REPLACE THE FEET WHEN YOU MOVE THE MONITOR.
10 Warning For proper installation and mounting it is required. Switch on the power of each of the devices * When connected with a computer, switch on the power of the screen display position or distortion is required.
9. This monitor cannot be used without one unit, maximum.)
3. MODEL # PX-42VPU1-ST STAND...
42PD2/50PD1 - Page 13
... with the supplied power cable.
13 Terminal Board L/R
IN
OUT
VIDEO
S-VIDEO
15 10
HIGH 75Ω
V
H/CS
11
B
16
G
RGB2 R
12
13
RGB1
17
14
AC-IN
18
Insert the prongs completely. * for PLUGGABLE EQUIPMENT, tee
socket-outlet shall be installed near the equipment and shall be easily accessible.
10 DIP SW Sets the various...
42PD2/50PD1 - Page 17
... should be used.
DIP Switch Functions and Settings 1234
ON
Factory Default Settings
PIn No. No. 2: On/off the main power before making settings. Monitors for which the reception of wireless remote control * When using multiple units under wireless remote control operation, the remote
control signal also enters other monitors and may be set to "OFF." * Be sure to be...
42PD2/50PD1 - Page 18
... of the personal computer you are not input. For information about 4 seconds Remote control in standby mode Power cord not connected
* Standby suspend, off in about the power management setting method, see the operating system (OS) manual of the display when the keyboard or the mouse have not been used with a personal computer based on...
42PD2/50PD1 - Page 20
... about your computer's video output requirements and any special identification or configuring your monitor's image and monitor may require. Connecting Your PC or Macintosh Computer
Connecting your PC or Macintosh computer to your plasma monitor will enable you need to install a new board, see the manual that comes with your new graphics board for installation instructions. 3.
Turn on...
42PD2/50PD1 - Page 22
... the remote control.
4. Select The Computer Or Video Source Press the "VIDEO" or "RGB 1" "RGB 2" or "RGB 3"(computer) button on the remote control, the monitor will go into its standby mode and the POWER/STANDBY indicator will be in . Turning Off The monitor. After you turn to green and the monitor will become ready to select your plasma monitor ensure...
42PD2/50PD1 - Page 47
... the power supply circuit or, one more fans have been damaged. If the problem persists, contact your dealer or authorized NEC Service Center.
Nothing appears on and then the POWER/STANDBY indicater blinks. Picture is disturbed. External equipment has been incorrecty connected. Incorrect input selection. • Improper control setting.
Press correct RGB1, RGB2, RGB3, or VIDEO button...
42PD2/50PD1 - Page 48
... to change without notice.
48 Specifications
PlasmaSync 42PD2 (Model PX-42VP2A)
Plasma Screen
RGB Input Terminals
RGB Output Terminals THROUGH OUT
Video Input Terminals VIDEO S-VIDEO
Video Output Terminals THROUGH OUT THROUGH OUT (S-VIDEO)
External Control (IN/THROUGH OUT)
Synchronization Range Maximum Resolution Power Supply Current Rating Power consumption Dimensions Weight Environmental...
42PD2/50PD1 - Page 49
...75 Ohms unbalanced, Sync-negative. PlasmaSync 50PD1 (Model PX-50VP1A)
Plasma Screen
RGB Input Terminals
RGB Output Terminals THROUGH OUT
Video Input Terminals VIDEO S-VIDEO
Video Output Terminals THROUGH OUT THROUGH OUT (S-VIDEO)
External Control (IN/THROUGH OUT)
Synchronization Range Maximum Resolution Power Supply Current Rating Power consumption Dimensions Weight Environmental Considerations...
NEC PX-50VP1A Reviews
We have not received any reviews for NEC yet.