NEC MM2000 Support and Manuals
Popular NEC MM2000 Manual Pages
MM2000B : MM2000B User Manual - Page 1
Multimedia Switcher for DLP Cinema® Projector
MM2000
User's Manual
NEC Viewtechnology, Ltd.
MM2000B : MM2000B User Manual - Page 2
...installed as possible, and should be read carefully to avoid problems.
WARNING TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
ALL SERVICING MUST BE DONE BY QUALIFIED SERVICE PERSONNEL.
CAUTION
• In order to reduce any part... supply
of your MM2000 Switcher and keep the manual handy for use... Safeguards
These safety instructions are designed to provide...
MM2000B : MM2000B User Manual - Page 3
...support branches for peripheral device wiring that vents are reused and recycled in each Member State requires that might have the object removed by a qualified service... your switcher.
In Europe
NEC Europe, Ltd. / European...unclear points, malfunctions and repairs of space between your ...off the Main Power switch, set the Switcher to the current ...not handle the parts on the electrical...
MM2000B : MM2000B User Manual - Page 11
The accessory contents are as follows:
• Multimedia Switcher (MM2000)
1. Introduction
• Ferrite clamp core (for Power cable / RGB cables) x2
• Band x2
• User's Manual User's Manual
(For Japan)
• Power cable x3
• Power cable for Japan
(AC100V)
• Power cable for North America
(AC120V)
• Power cable for Europe
(AC230V...
MM2000B : MM2000B User Manual - Page 13
...crystal display screen shows the condition or the error message of the E button executes the selection.
8....this switch except for a minimum of a setup inside the Switcher are in standby mode. ...service personnel touched this button for the service personnel. NOTE To turn on and off the Switcher, press and hold this switch, the Switcher breaks down, and contents of 1 second.
5 Control...
MM2000B : MM2000B User Manual - Page 14
.... Introduction
1-3-4. DVI output B terminal (DVI-D 24P)
This terminal is used for the service personnel. It is for high 8-bit output of DVI. AC IN terminal
Connect the AC...
6 Use a commercially available DVI-D signal cable (single link).
8. PC card slot
Set a wireless LAN card, and you can control this unit by exclusive command via RS-232C interface with a PC. Connect this unit ...
MM2000B : MM2000B User Manual - Page 16
...
Using a thinner cable than the above can degrade image quality or cause no signal or an error occurs. Option Boards
MM-SDI Interface Board (Option)
The SDI signal input board is present.
... 23. • Cycle the unit power in the following cases. • The status indicator is lighting in orange. • The image of input interface is selected. Introduction
1-3-6....
MM2000B : MM2000B User Manual - Page 21
... When installing or removing the board from the Switcher, do so after turning off the main power switch of the Switcher. 4 Tighten the 2 screws located at the input terminals portion of the same model can also be inserted in a safe place. • Please do so could enter the interior and cause breakdown...
MM2000B : MM2000B User Manual - Page 22
... standalone mode.
[Example of the switcher (standalone mode). 2. Installation
2-5. In addition, when the switcher is provided with LAN] Touch panel controller (option)
Server
NC series projector
Hub
LAN cable* (not supplied) PC
LAN
PC MM2000
* When the switcher and PC are connected, use a mode for setting and adjustment of Connection with a LAN port (RJ...
MM2000B : MM2000B User Manual - Page 24
...
POWER
Steady green light
16 Turn on the main power to the Switcher, press the Main Power switch to use. Refer to the Projector User's Manual for a minimum of a device connected to the Switcher.
• The Switcher has two power switches: main power switch and POWER button.
3. Projecting an Image
Specify...
MM2000B : MM2000B User Manual - Page 29
... turned on.
page page 15
page 16 - For control of the switcher, contact the person in charge of the PC. Check the resolution of setting and adjustment.
6. Check that the power cable is plugged in the following pages. Troubleshooting
Before asking for instructions or repair.
6-1-1. If the trouble cannot be shifted in and that the main...
MM2000B : MM2000B User Manual - Page 30
...signal that is normal.
This sometimes sets the external output signal to the PC. Error code list
Error messages relating to switch. 6. In many cases, this mode can handle, the...+ F8 Fn + F10
NEC, Panasonic, Gateway, SOTEC HP TOSHIBA, SHARP, MITSUBISHI SONY, IBM, HITACHI DELL, EPSON FUJITSU
Normally, each error code. Please inquire your
owner's manual. Timing for each time ...
MM2000B : MM2000B User Manual - Page 32
...Specifications
Model Number Image Input
Image Input (Optional board specifications)
Image output Image signal processing
Input Slot MM-VIDEO (Standard board) MM-RGB (Standard board) MM-DVI (Option board) MM-SDI (Option board) Output Terminal USB Port LAN Port PC Control...dual link supported Maximum ...service personnel) RJ-45 x 1 D-Sub 9 pin x 1 (For service personnel)
Input / Output Terminals
24
MM2000 : Alternative Content Processors Brochure - Page 1
...Digital Cinema Projectors
Digital Cinema Projector Series
MM2000 and MM2000B alternative content processors
Ideal as an independent unit (MM2000) or as a built-in MM2000B is compatible with all models of the NEC Digital Cinema Projector Series, while the built-in enhancement (MM2000B) of NEC digital cinema projectors, the MM2000 and MM2000B convert video signals from various external sources...
NEC MM2000 Reviews
Do you have an experience with the NEC MM2000 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for NEC yet.
Earn 750 points for your review!