NEC M491-MPi4E Support and Manuals
Get Help and Manuals for this NEC item
View All Support Options Below
Free NEC M491-MPi4E manuals!
Problems with NEC M491-MPi4E?
Ask a Question
Free NEC M491-MPi4E manuals!
Problems with NEC M491-MPi4E?
Ask a Question
Popular NEC M491-MPi4E Manual Pages
External Control Guides M & ME Series - Page 24
... / 93 The controller requests the Monitor to reply with current Brightness setting and capability to support this operation. 6.1.2.1. No error. '00'(30h, 30h) : Operation code page number is 0. '10'(31h, 30h) : Operation code is 10h (in the page 0). '00'(30h, 30h) : This operation is "Set parameter" type. '00'-'64'(30h, 30h, 36h, 34h)
: Brightness max value...
External Control Guides M & ME Series - Page 25
The controller request the monitor to check the Brightness setting. (Recommended)
25 / 93 No error. '00'(30h, 30h) : Operation code page number is 0. '10'(31h, 30h) : Operation code is 80(0050h) .
NEC Command
12/28/2020
|
Header
|
Message
| Check code | Delimiter |
|SOH-'0'-Monitor ID-'0E'-'0A'| STX-'00'-'10'-'00'-'50'-ETX| BCC
| CR
|
Message
'00'(30h...
External Control Guides M & ME Series - Page 27
... sensor which you want to read .
6.2.1.1. No error. '02'(30h, 32h) : Operation code page number is 2. '78'(37h, 38h) : Operation code is 78h (in the page 2). '00'(30h,...NEC Command
| Header
|
Message
|
| |
| SOH-'0'-Monitor ID-'0E'-'0A' | STX-'02'-'78'-'00'-'01'-ETX | BCC | CR |
Message
'02'(30h, 32h) : Operation code page number is 2. '78'(37h, 38h) : Operation code is "Set...
External Control Guides M & ME Series - Page 28
... 2). '00'(30h, 30h) : This operation is "Set parameter" type. 'FF'-'FF'(46h, 46h, 46h, 46h)
: Maximum value. '00'-'32'(30h, 30h, 33h, 32h)
: The temperature is 25 degrees Celsius.
NEC Command
|
Header
| Message
| ||
|SOH-'00'- No error. '02'(30h, 32h) : Operation code page number is 2. '79'(37h, 39h) : Operation code is 2's complement.
| Temperature [[Celsius] |
Readout...
Installation Guide - Page 2
NEC Display Solutions of 19
www.necdisplay.com
MultiSync M Series Large Format Displays
Page 2 of America, Inc. If for proper ventilation
NOTE: ...Face Up orientation is on HIGH and if the ambient temperature stays less than the 100mm, extra
ventilation may be counterclockwise. Contact NEC for these models only if the fan setting is supported for design review and recommendations.
User Manual - Page 5
...installed and used in accordance with Part 15 of the FCC Rules. Operation is subject to the following booklet, prepared by NEC Display Solutions of America, Inc. No.:
(630) 467-3000
Type of Product:
Display Monitor
Equipment Classification:
Class B Peripheral
Model:
M431, M491...TV Interference Problems." This booklet is available from using
this device. (6) This manual is ...
User Manual - Page 6
... prevent injury to you should be prohibited. Do not use of the product, this manual uses a number of symbols
Indicates a warning or caution. Important Information
Safety Precautions and Maintenance
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONITOR:
About the Symbols
To ensure safe and...
User Manual - Page 8
... parts, and then secure the product with the installation instructions.
The safety wire must be retained and relocated, the same considerations as :
• ALWAYS use furniture that can safely support...or damage to the product caused by the manufacturer of the product set.
• ALWAYS use stands or installation methods recommended by tipping over , pulled or grabbed.
• ...
User Manual - Page 17
If a problem is detected, please refer to the table top stand manual of ST-401 and ST-43M for signs of qualified installation professionals. Prevent Tipping
WARNING: Please refer to "WARNING 7" and "WARNING 9". • Please refer to qualified personnel for service.
• Regularly check the mounting location for "structure of the monitor. M651
Cord or...
User Manual - Page 33
...instructions in , turned on page 30.
See "HDMI-CEC Command" on , it supports CEC and CEC is enabled. When supported, the monitor's remote control can be used to "Specifications" for the supported...These settings can...guide you are unable to a Media Device with HDMI
Connect using a single HDMI cable for [CEC]. 5. Supports HDCP (High-bandwidth Digital Contents Protection) coding...manual. 6.
User Manual - Page 34
... audio equipment.
Use the + -
Use the buttons to the user's manual supplied with the "Change Language function". After selecting the device, wireless remote control operation functions...the monitor by the included ARC supported HDMI cable. Press the Menu button to enable CEC.
buttons to highlight [MODE1] or [MODE2], then press SET/POINT ZOOM button to open the...
User Manual - Page 43
.... A table listing all options is a brief summary of the default picture modes, manually adjust the color settings, adjust the aspect ratio, and adjust other settings related to the picture. INPUT: Select settings related to an Option Board if installed. AUDIO: Adjust volume, balance, equalizer, and select settings related to the audio. SYSTEM: View the monitor information...
User Manual - Page 47
Chapter 5 Advanced Operation
This Chapter Includes:
>> "Creating a Power Schedule" on page 44 >> "Using Picture Modes" on page 45 >> "Setting Security and Locking the Monitor Controls" on page 46 >> "Password Security" on page 46 >> "Locking the Button Controls" on page 48 >> "Setting the Remote Control ID Function" on page 50
English−43
User Manual - Page 63
... for class2. Type in the hostname of the CRESTRON SERVER. This name is the monitor's model name. The password must be managed and controlled from the controller. Set a password for the HTTP server. CRESTRON ROOMVIEW compatibility The monitor supports CRESTRON ROOMVIEW, allowing multiple devices connected in 2005. Network Service Settings
Click on "NETWORK SERVICE" on the network.
Raspberry Pi Compute Module Setup Guide - Page 35
... can be changed to enable the lirc-rpi module #dtoverlay=lirc-rpi
b. Make sure the display support is not included with the OS, it can be installed using "lirc"
1. Select the ADVANCED SETTINGS option after COMPUTE MODULE. a. On the NEC display select the SLOT menu on the OSD. Confirm that the IR SIGNAL is...
NEC M491-MPi4E Reviews
We have not received any reviews for NEC yet.