NEC M491-PC5 Support and Manuals
Get Help and Manuals for this NEC item
View All Support Options Below
Free NEC M491-PC5 manuals!
Problems with NEC M491-PC5?
Ask a Question
Free NEC M491-PC5 manuals!
Problems with NEC M491-PC5?
Ask a Question
Popular NEC M491-PC5 Manual Pages
External Control Guides M & ME Series - Page 24
...this operation. 6.1.2.1. The monitor replies with the current brightness setting and capability to support this operation. (Get parameter)
6.1.1.1. Typical procedure example
The following is 10h (in the OP code page 0).
6.1.2. NEC Command
| Header
| Message
|
|
|SOH-'00'- Step 2. No error. '00'(30h, 30h) : Operation code page number is 0. '10'(31h, 30h) : Operation...
External Control Guides M & ME Series - Page 25
...'-'10'-'00'-'00'-'64'-'00'-'50'-ETX|BCC |CR|
Message
'00'(30h, 30h) : Result code. No error. '00'(30h, 30h) : Operation code page number is 0. '10'(31h, 30h) : Operation code is 80(0050h) .
Step 3. NEC Command
12/28/2020
|
Header
|
Message
| Check code | Delimiter |
|SOH-'0'-Monitor ID-'0E'-'0A'| STX-'00'-'10'-'00'-'50'-ETX| BCC...
External Control Guides M & ME Series - Page 27
...'02'(30h, 32h) : Operation code page number is 2. '78'(37h, 38h) : Operation code is #1.
27 / 93 NEC Command
|
Header
| Message
| ...Set parameter" type. '00'-'03'(30h, 30h, 30h, 33h)
: Number of the built-in temperature sensors. External_Contorl_M_ME_Series_EN_Rev1.0.md
12/28/2020
6.2. No error. '02'(30h, 32h) : Operation code page number is 2. '78'(37h, 38h) : Operation code...
External Control Guides M & ME Series - Page 28
...the monitor to send the temperature from the selected sensor. 6.2.3.1. NEC Command
|
Header
| Message
| ||
|SOH-'00'- ID -'D'-'12'|...Set parameter" type. 'FF'-'FF'(46h, 46h, 46h, 46h)
: Maximum value. '00'-'32'(30h, 30h, 33h, 32h)
: The temperature is 25 degrees Celsius. External_Contorl_M_ME_Series_EN_Rev1.0.md 6.2.3. Step 3. Step 4. No error. '02'(30h, 32h) : Operation code...
Installation Guide - Page 2
Face Up orientation is supported for design review and recommendations.
Contact NEC for these models only if the fan setting is to be used in order to be necessary. If the distances are less than 35 degrees Celsius. NEC Display Solutions of 19
Rotation/Face Up:
If display is on HIGH and if the ambient...
User Manual - Page 5
...Model:
M431, M491, M551, M651
• The intended primary use a shielded signal cable. This booklet is available from using
this device. (6) This manual is commonly provided to all regions so they may contain descriptions that interference will not be responsible for any questionable points, errors... (3) and (4), NEC will not occur in a particular installation. Cable Information
...
User Manual - Page 6
...injury or damage to repair the product on your dealer for repairs. Indicates a prohibited action... understand them thoroughly before reading this manual. Examples of electric shocks.
Failing ...PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONITOR...cracks or unnatural wobbling, please refer servicing to qualified service personnel. Indicates a mandatory action. ...
User Manual - Page 17
... 9". • Please refer to "WARNING 7". Install the logo ornament with the mounting equipment. If a problem is used for installing the logo ornament. (Recommended Fasten Force: 30-40 N•cm).
NOTE: Do not use any other problems that may occur over time. WARNING: Please refer to qualified personnel for service.
• Regularly check the mounting location...
User Manual - Page 33
... image correctly due to different HDMI specifications. • If you through configuring [CEC] in , turned on, it supports CEC and CEC is enabled.
Navigate to [ADVANCED] then to open the OSD menu. 3. Supports HDCP (High-bandwidth Digital Contents Protection) coding, a type of each input connector. Refer the device's product manual. 6. Select [YES] under [SEARCH DEVICE...
User Manual - Page 34
... HDMI-CEC compatible device input switches to HDMI1 (ARC) by the included ARC supported HDMI cable.
This CEC function supports Feature Abort. If the monitor is turned on, the monitor connected to HDMI ... press SET/POINT ZOOM.
also go into standby while an HDMICEC compatible device is in standby mode or on the wireless remote control can also be able to the user's manual supplied ...
User Manual - Page 43
... picture modes, manually adjust the color settings, adjust the aspect ratio, and adjust other settings related to an Option Board if installed. Configure the Media Player settings.
Below is located...error occurs in "OSD Controls List" on -screen display menu, or perform a factory reset. INPUT: Select settings related to the audio. AUDIO: Adjust volume, balance, equalizer, and select settings...
User Manual - Page 47
Chapter 5 Advanced Operation
This Chapter Includes:
>> "Creating a Power Schedule" on page 44 >> "Using Picture Modes" on page 45 >> "Setting Security and Locking the Monitor Controls" on page 46 >> "Password Security" on page 46 >> "Locking the Button Controls" on page 48 >> "Setting the Remote Control ID Function" on page 50
English−43
User Manual - Page 63
...The default name is a network interface standard that JBMIA established.
NOTE: PJLink is the monitor's model name. This function is a standardization of different manufacturers. Set a password for managing from a computer or a controller.
CRESTRON CONTROL for PJLink*. Sets your password. This name is shown when searching for class2. Up to 60 alphanumeric characters can be...
User Manual - Page 77
... https://www.nec-display.com/dl/en/manual/raspberrypi/
English−73
A Python programming language based SDK (Software Development Kit) is also available for externally controlling the basic functions of checksums, and most functionality in the monitor can be controlled using a simple English-like syntax. Setup Guide" PDF document This document describes the features, installation...
User Manual - Page 85
... without a distribution amplifier at a lower number of audio in order to focus on the current monitor. Press the - This option is for manually configuring the TILE MATRIX settings that are automatically configured when using [AUTO TILE MATRIX SETUP].
NOTE: • Low resolution is mute). While the tile matrix is active, changing the aspect...
NEC M491-PC5 Reviews
We have not received any reviews for NEC yet.