NEC 42VP4D Support and Manuals
Get Help and Manuals for this NEC item
Popular NEC 42VP4D Manual Pages
User Manual - Page 4
... QUALIFIED SERVICE PERSONNEL. No maintenance other than 99.99 percent active cells. Please see the section "Plasma monitor cleaning procedure" on the next page. To avoid shock and fire hazards:
1. If you install the unit in an enclosure, make any kind of contact with any part inside . If the problem persists, contact your plasma monitor and keep the manual...
User Manual - Page 5
... during use with minimal contrast between colors.
* Note: Burn-in is installed. If the plasma monitor is the case with a soft brush nozzle attachment. 3. Set the ferrite cores on both ends of the power cable (supplied). Handle the unit carefully when installing it serviced by the warranty. In case of accident, unplug the power cord and...
User Manual - Page 6
..., and resolution E-41
External Control E-42
Table of the screen ..... E-1
Introduction E-2 Introduction to suit the movie E-28 Reducing burn-in the picture E-20 Setting the color temperature E-20 Adjusting the color to the Plasma Monitor .. E-15
OSM Controls E-16 Menu Operations E-16 Picture Settings Menu E-19 Adjusting the picture E-19 Setting the picture mode according to...
User Manual - Page 8
...; Plasma monitor
Ⅺ Power cord
Ⅺ Remote control with our special CCF. • 42VP4: Installed AR (Anti-Reflection) Filter 42VP4D: Installed AG (Anti-Glare) Filter • 42VP4: Body color is a seamless blend of the monitor using the stand (optional). At 42 inches, with your environment. Fasten the safety fittings to the holes in well with a 16:9 aspect ratio, the PlasmaSync...
User Manual - Page 11
... the unit.
!5 MULTI Not functional for the models covered in this manual.
!6 SELECT Not functional for the models covered in the main menu.
The available sources depend on the monitor. See page E-3. See page E-3.
RGB/PC can also be selected using the INPUT SELECT button on the settings of the main menu to go to...
User Manual - Page 15
... so, simply:
1. To connect a PC, Macintosh or compatible graphics adapter, simply:
1. Turn on the plasma monitor and the document camera. E-9 Connecting Your PC or Macintosh Computer
Connecting your PC or Macintosh computer to your plasma monitor will need to install a new board, see the manual that the RGB3 (DVI) terminal does not support analog RGB input source.
User Manual - Page 48
... 82H DFH 80H 60H C1H 01H 02H 83H
Note: Contact your local dealer for a full list of the plasma monitor by external equipment. External Control
Application
These specifications cover the communications control of the External Control Codes if needed.
12345 678 9
Communication Parameters
(1) Communication system Asynchronous
(2) Interface
RS-232C
(3) Baud rate
9600 bps
(4) Data...
User Manual - Page 55
... of the conventional model about specification."
Pin Name 1 No Connection 2 RXD (Receive data) 3 TXD (Transmit data) 4 DTR (DTE side ready) 5 GND 6 DSR (DCE side ready) 7 RTS (Ready to send) 8 CTS (Clear to NEC plasma monitors and communications control from external equipment. "Please also support the command of VP series and refer to the manual of connector: D-Sub...
User Manual - Page 57
... command 2, is a number used for the plasma monitor and 80H is BH (as follows. Bit1,Bit0 Unit ID distinction bit
11B
:Usually, a form (with no ID)
01B
:Set ID
00B
:Video wall ID
In the case...UA1,UA2)
Unit ID 1 and unit ID 2 are set up as in 3FH and 7FH), this indicates that the commands and data of the supported equipment have been received.
When making it operate using ID,...
User Manual - Page 58
When supporting Set ID by the command 1, 4 bits of low ranks of Set ID are set up .
2) Unit ID 2: Indicates the equipment receiving the signal. 1) Unit ID 1: Indicates the equipment sending the signal. When supporting Set ID by the command 1, 4 bits of higher ranks of Set ID are set up .
* Set ID : it is the apparatus number assigned to each plasma monitor.
5
User Manual - Page 66
... 80H 7FH 02H DATA00 DATA01 CKS
13 BRIGHT Gain Data
Function
The external control equipment changes the BRIGHT gain data of the
plasma c
Transmission Data
DFH 80H 60H 7FH 03H DATA00 DATA01 DATA02 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : CONTRAST ...07H
08.
CONTRAST Gain Data
Function
The external control equipment changes the CONTRAST gain data of the plasma
monitor. 07.
User Manual - Page 67
... PICTURE Gain Flag
01H
DATA01 : BRIGHT Gain Flag
08H
09.
SHARPNESS Gain Data
Function
The external control equipment changes the SHARPNESS gain data of the
plasma monitor. Transmission Data
DFH 80H 60H 7FH 03H DATA00 DATA01 DATA02 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : SHARPNESS Gain Flag
06H
DATA02 : SHARPNESS Gain...
User Manual - Page 68
... during video.
00H : 0
01H : +01
:
20H : +32
ACK
15
10. COLOR Gain Data
Function
The external control equipment changes the COLOR gain data of the plasma
monitor. TINT Gain Data
Function
The external control equipment changes the TINT gain data of the...
User Manual - Page 69
... the still picture input of a personal computer.) 03H : THEATER2(It cannot choose in the still picture input of the plasma monitor. PICTURE MODE Select Function
The external control equipment sets the picture mode of the plasma monitor. 7FH 60H 80H 7FH 02H DATA00 DATA01 CKS
DATA00 : USER PICTURE Gain Flag
01H
DATA01 : TINT Gain Flag...
User Manual - Page 96
... : 2nd character of the product code
: DATA11 : 12th character of your plasma monitor is "PX-42VP4G", the returned codes would be as follows. DATA00:1FH, DATA01:27H, DATA02:80H, DATA03:04H, DATA04:02H, DATA05:25H, DATA06:1FH, DATA07:04H, DATA08:16H, DATA09:96H, DATA10:96H, DATA11:96H
43 49.
MODEL NAME Request Function
The external control...
NEC 42VP4D Reviews
We have not received any reviews for NEC yet.