Maytag MEDE200XW Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag MEDE200XW manuals!
Problems with Maytag MEDE200XW?
Ask a Question
Free Maytag MEDE200XW manuals!
Problems with Maytag MEDE200XW?
Ask a Question
Most Recent Maytag MEDE200XW Questions
My Maytag Dryer Less Than A Year Old Over Heats And Turn It's Self Off.
(Posted by maryanndhoover 11 years ago)
I Unhook My Heating Element And Know I Don't Know Were The Wires Go
I have a maytag bravo dryer med6400tqo I unhook the heating element and forgot were the 3 wires go
I have a maytag bravo dryer med6400tqo I unhook the heating element and forgot were the 3 wires go
(Posted by Cece1227 11 years ago)
Can This Dryer Be Stackable?
(Posted by blondy337 12 years ago)
How Do I Get Installing Instruction Manual?
(Posted by JEANMCC 13 years ago)
Popular Maytag MEDE200XW Manual Pages
Owners Manual - Page 3
... GAS:
• Do not try to prevent property damage, personal injury, or death.
- do not use gasoline or other appliance.
- The dryer must be performed by a quali ed installer, service agency, or the gas supplier.
3 IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70.
Owners Manual - Page 5
..., if desired.
USING AUTO CYCLES
Auto Cycles automatically match the cycle setting to the type of fire electric shock, or injury to begin . Place laundry in the dryer. Select the desired AUTO cycle.
5. Press POWER/CANCEL. 4. Stopping Your Dryer
To stop the dryer at any time Open the door or press START/PAUSE once.
Shut...
Owners Manual - Page 6
... DRY
Low
20
Clothes to complete drying, if needed .
Type of load you dry a similar load. A sensor detects the moisture in your cycle. pillows, padded bras, stuffed toys Plastic - Cycles
NOTE: Not all models.
Cycle Control knob
Auto Cycles
Auto Cycles allow you are not available when using the Air Dry setting.
6 Press...
Owners Manual - Page 9
... properly installed. Separate the load items and restart the dryer.
■■ Is the correct power supply available? Make sure leveling legs are secure in dryer base. 4. Replace all parts and panels before servicing. To change the drum light
1. Using a Phillips head screw driver, remove the screw located in dryer base. 3. Replace the bulb with the screw.
4. TROUBLESHOOTING
First...
Owners Manual - Page 10
... replace exhaust vent with lint, restricting air movement? Long venting will change the amount of the cycle? See the Installation Instructions. Sides and front of dryer require a minimum of 1" (25 mm) of airspace, and the rear of garments being dried. Cycle time too short
■■ Is the automatic cycle ending early? Change the dryness level setting...
Owners Manual - Page 12
...in accordance with Maytag's published installation instructions.
10.
EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
In Canada, call 18006889900.
Replacement parts or repair labor if this major appliance is used for future reference. Service calls to know...
Installation Instructions - Page 2
... tell you how to potential hazards that can happen if the instructions are very important. This symbol alerts you to reduce the chance ... safety messages in this manual and on your appliance.
All safety messages will follow instructions. These words mean:
DANGER
You can be killed or seriously injured if you don't immediately follow instructions.
DRYER SAFETY
Your safety and ...
Installation Instructions - Page 3
... your dryer.
Parts needed :
Parts supplied (all models):
Flat-blade screwdriver
#2 Phillips screwdriver
Leveling legs (4) Parts supplied (steam models):
Wire stripper (direct wire installations)
Tin snips (new vent installations)
"Y" connector
Short inlet hose
1/4" nut driver (recommended)
Vent clamps
Adjustable wrench that all parts are included. Check existing electrical supply...
Installation Instructions - Page 4
... power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa). spacing for companion appliances and clearances for ease of installation and servicing; If a closet door or louvered door is greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Number 279810. You may...
Installation Instructions - Page 5
...)
48 in.2 (310 cm2)
Back view: Electric
61/4"
(159 mm)
4" (102 mm)
3" (76 mm)
24 in.2 (155 cm2)
1" (25 mm)
1" (25 mm)
Cabinet installation (dryer only):
281/8"
(715 mm)
31/2"
(89 mm)
7" (178 mm)
18" (460 mm)
14" (358 mm)
NOTE: Most installations require a minimum of installation and servicing.
■■ Additional clearances might be required...
Installation Instructions - Page 6
... or Service" section in your dealer.
Mobile home installations require: ■■ Metal exhaust system hardware, available for Mobile home construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240 MH. latest edition and all mobile home installations.
A copy of the above code standards can be at least twice as large as dryer exhaust opening.
The kit...
Installation Instructions - Page 7
... dryer for electrical connection and to whether the dryer is properly installed and grounded in back or other injury.
1. All current-carrying wires must be either green or bare. Check with a qualified electrician or service representative or personnel if you are in leveling legs
diamond marking
Examine leveling legs, find diamond marking. SAVE THESE INSTRUCTIONS
To...
Installation Instructions - Page 14
... extend into any object that
may result in reduced airflow and poor performance.
■■ Do not install in final dryer location.
■■ Remove excess to avoid crushing and kinking.
Venting
Venting Requirements
Exhaust hoods: ■■ Must be used for best drying performance and to avoid sagging and kinking that may obstruct exhaust (such as...
Installation Instructions - Page 18
... faucet
2. Not Level
LEVEL
Not Level
18 Level dryer
1.
Dryer vent must be level for leaks around "Y" connector, faucets, and hoses. 6.
Using a 4" (102 mm) clamp, connect vent to exhaust outlet in place, remove cardboard from under dryer. Level Dryer
Check for the moisture sensing system to back. Connect vent to exhaust outlet
Place level here
Check levelness...
Installation Instructions - Page 19
... or Service" section in your "Use and Care Guide" for levelness. q Remove film on your washer and dryer: A stack kit, Part Number 8572546 is first heated. Excessive scale buildup may lead to order. For further information, see what was skipped. Troubleshooting
See your "Use and Care Guide". Once legs are set in your "Use and Care Guide". Be sure vent is...
Maytag MEDE200XW Reviews
We have not received any reviews for Maytag yet.