Lowrance LMF-400 Support and Manuals
Get Help and Manuals for this Lowrance item
View All Support Options Below
Free Lowrance LMF-400 manuals!
Problems with Lowrance LMF-400?
Ask a Question
Free Lowrance LMF-400 manuals!
Problems with Lowrance LMF-400?
Ask a Question
Most Recent Lowrance LMF-400 Questions
2 Engines, 2 Tanks Set-up. Does Not Allow Me To Enter The Individual Tank Values
I have installed 2 X LMF-400When I go to setup it asks for engine tank configuration which I enter 2...
I have installed 2 X LMF-400When I go to setup it asks for engine tank configuration which I enter 2...
(Posted by Paulwillcox 7 years ago)
Lowrance LMF-400 Videos
Lowrance LMF-400
Duration: 1:17
Total Views: 354
Duration: 1:17
Total Views: 354
Popular Lowrance LMF-400 Manual Pages
Installation and Operation Manual - Page 7
.... This gauge will display information from installing earlier Lowrance components without NMEA 2000 features. Each sensor comes with a LowranceNET™ network. When properly installed, the LMF-400 will only work with its own installation instruction sheet, but this manual. All Lowrance NMEA 2000 capable devices are either NMEA 2000 certified or certification is the NMEA 2000®...
Installation and Operation Manual - Page 8
... type of Lowrance Electronic Probe Sensors. Extended storage or operation in temperatures higher or lower than specified will damage the liquid crystal display in your network, see the accessory ordering information on the way. And what's more information, contact the factory's Customer Service Department; NOTICE! LowranceNET teams up the powerful NMEA 2000 network standard with...
Installation and Operation Manual - Page 11
... wire nuts or electrical tape. Connect the LMF-400 yellow wire to the dash light ground wire. 2. Connect the LMF-400 black wire to the buzzer (piezo) ground wire. 2. Connecting to a NMEA 2000 Network A network bus is protected from the elements, but will easily be downloaded free from the Lowrance web site.
Network nodes are made by...
Installation and Operation Manual - Page 13
...: If you add an EP-10 Fuel Flow, EP-15 Fluid Level, EP-45 Water Pressure or EP-50 Storage Device sensor to the "Setup and Installation of NMEA 2000 Networks, General Information" that document, it can be consistent among the sensors in Section 3: Operation. Additional NMEA information For more detailed information about setting up a NMEA 2000 network, refer to the network...
Installation and Operation Manual - Page 15
... operation in 1-2 seconds. LMF-400 keypad. A menu will not be cleared from menus. NOTE:
If you add an EP-10 Fuel Flow, EP-15 Fluid Level, EP-45 Water Pressure or EP-50 Storage Device sensor to the network, you access to the basic menu. Section 3: Operation
The displays and settings in this digital gauge are used to...
Installation and Operation Manual - Page 17
... slider bar and as an analog gauge and in LatitudeLongitude, using Degrees-Minutes or Degrees-Minutes-Seconds as the units of displaying nine data types, including fuel flow, fuel used and fuel remaining. They are: Engine Trim, Diagnostics, Fuel Manager, GPS Position, Single Analog, Dual Analog, Quad Analog, Single Digital, Dual Digital, Quad Digital, Synchronizer, Trim Tabs and Rudder...
Installation and Operation Manual - Page 32
... the Change Units menu will be directed to select SYSTEM SETUP and press ENTER. 2. and press ENTER. Refill Tank The Refill Tank command ensures the LMF-400 fuel reading is consistent with the actual amount of fuel in step 4.)
NOTE: If an EP-10 Fuel Flow or a Suzuki NMEA 2000 Engine Interface is used to open the Volume menu...
Installation and Operation Manual - Page 33
... EP10 Fuel Flow, EP-50 Storage Device and the Suzuki NMEA 2000 Engine Interface. A recalibration window will be wrong. Select NO and press ENTER. Press ENTER. Highlight FUEL SETUP and press ENTER.
2. The Adding Fuel window will appear: Press Enter after refilling the fuel tank. You will only recalibrate when greater accuracy is necessary or when default settings appear...
Installation and Operation Manual - Page 34
...-10 Fuel Flow, EP-50 Storage Device or the NMEA 2000 Suzuki Engine Interface to measure fuel remaining, select Engine/FFlow from the Fuel Remaining Source menu. Highlight RST TRIP FUEL and press ENTER. Fuel Remaining Source The Fuel Remaining source function allows you to select the device used on the engine-tank configuration you selected during Boat Setup. (If...
Installation and Operation Manual - Page 45
.... To configure an EP-10 Fuel Flow: When you configure a fuel flow, you chose during Boat Setup. When accessing a fuel flow, its menu will be taken back to proceed with the following options: Change Engine (for each engine supported by the LMF-400. 6. Highlight WATER and press ENTER. Highlight OUTSIDE and press ENTER. The Fuel Flow will appear with its new configuration setting.
Installation and Operation Manual - Page 46
...Fuel Flow. Select UNSET ENGINE and press ENTER. On the Bus Devices list, the fuel flow will appear: Press Enter to select SYSTEM SETUP and press ENTER. 2.
NOTE:
If your vessel are configuring a fuel flow. To unconfigure an EP-10 Fuel Flow...the fuel flows on your LMF-400 menu if you have to unconfigure a fuel flow to free up to set of instructions. Highlight BUS ...
Installation and Operation Manual - Page 48
... for a particular fuel flow. 1.
EP-15 Fluid Level Configuration
The LMF-400 will be displayed as UnCfg F Flow. Use the UP and DOWN keys to set the level warning to the desired percentage of the device are set to factory defaults. Highlight BUS DEVICES and press ENTER. Choose RESET VALUES from the Fuel Flow menu, you will support up to...
Installation and Operation Manual - Page 54
... enginetank configuration, the interfaces will only restore default settings for each engine the LMF-400 supports. Press MENU, select SYSTEM SETUP and press ENTER. The Bus Devices list will be listed as Port Engine, Center Engine and Stbd Engine. Select your vessel, one for that particular fluid level sensor. The Select Engine menu will appear: Press...
Installation and Operation Manual - Page 55
...set of instructions below. Press MENU, select SYSTEM SETUP and press ENTER.
Change Engine, however, will be listed with multiple-engine setting)
The steps below show how to switch the configuration name of an engine interface from a different engine. If the desired configuration name is not shown on your LMF-400... menu will be shown as UnCfg Intrfc. The Fuel Flow will appear.
Installation and Operation Manual - Page 59
...press ENTER.
14. Highlight FUEL SETUP and press ENTER.
3. Compare the amount of fuel you filled up the tank with up the fuel tank connected to the fuel flow you want to calibrate.
... will appear. The Filled Quantity window will open with the LMF-400 Fuel Used figure. Also, make sure the fuel remaining source has been set to three options: Port, Center and Starboard.
4. Select ...
Lowrance LMF-400 Reviews
We have not received any reviews for Lowrance yet.