Lowrance EP-60R Fuel Flow Sensor Support and Manuals
Get Help and Manuals for this Lowrance item
View All Support Options Below
Free Lowrance EP-60R Fuel Flow Sensor manuals!
Problems with Lowrance EP-60R Fuel Flow Sensor?
Ask a Question
Free Lowrance EP-60R Fuel Flow Sensor manuals!
Problems with Lowrance EP-60R Fuel Flow Sensor?
Ask a Question
Most Recent Lowrance EP-60R Fuel Flow Sensor Questions
Fuel Flow Sensor Mounting
If the fuel flow sensor is installed to ensure flow in the direction of the arrow can it be mounted ...
If the fuel flow sensor is installed to ensure flow in the direction of the arrow can it be mounted ...
(Posted by ostermiller 3 years ago)
Popular Lowrance EP-60R Fuel Flow Sensor Manual Pages
Installation Configuration and Calibration Instructions - Page 1
... has introduced a line of the installation instructions before drilling any holes in boats.
Fuel Flow module
NMEA 2000 red connector
The EP-60R Fuel Flow sensor.
1
All Lowrance NMEA 2000 capable devices are either NMEA 2000 certified or certification is significantly different from installing earlier Lowrance components without NMEA 2000 features. NMEA 2000 is the communication bus...
Installation Configuration and Calibration Instructions - Page 2
... to female blue adapter cable. If this sensor with diesel engine fuel systems. The EP-60R is also compatible with a flow rate of 40 gallons per hour, the back pressure will be connected to the NMEA 2000 data format. The EP-60R Fuel Flow, like the other LowranceNet Electronic Probe (EP) sensors, is the first sensor you are connecting, you may require a software upgrade to 45 gallons...
Installation Configuration and Calibration Instructions - Page 3
....
For complete instructions on setting up any items needed to avoid accidental fuel leakage in an area where vibration is extremely flammable.
We assume you start or shut any Y or T in , fuel flow direction arrow, which should be pointing up. The EP-60R Fuel Flow was designed to clean up a new NMEA 2000 network or expanding an existing one EP-60R sensor per engine...
Installation Configuration and Calibration Instructions - Page 4
To engine
Flow direction
From tank
Push the fuel line onto the hose barb, then tighten the hose clamp.
NOTE:
You must install an in -line 3/8" splice barb. We strongly recommend that you intend to remove a clogged EP-60R fuel sensor or fuel filter and restore engine operation if the fuel filter fails. Slide a clamp over the hose coming from...
Installation Configuration and Calibration Instructions - Page 9
... to the segment covering EP-60R Fuel Flow Configuration. The default setting is the first time you will notice the LMF-200 does not have turned on the screen, press MENU. With Boat Setup highlighted on your LMF-200, you will have already completed Boat Setup, skip ahead to your LMF-200 instruction manual for more than one tank...
Installation Configuration and Calibration Instructions - Page 10
... three engines with Boat Setup highlighted. The Setup screen will open the Tank Size window. 4.
Use the UP and DOWN keys to default settings. That will appear with one fuel flow sensor for each engine.
...options: Eng/FFlow and Fuel level.
3. It will appear.
10 Highlight FREM SRC and press MENU. Select ENG/FFLOW and press MENU. EP-60R Fuel Flow Configuration
The LMF-200 can now...
Installation Configuration and Calibration Instructions - Page 11
...engine. If all the fuel flows on your unit is available, follow the first set of a fuel flow from Port to switch the configuration name of instructions. The steps below show...Engine command to select SYSTEM SETUP and press MENU. 2. To unconfigure a fuel flow:
You will appear. 3. To reconfigure a fuel flow:
You will be configured as UNCFG FF. The fuel flow will be taken back to...
Installation Configuration and Calibration Instructions - Page 13
... Remaining Source; Press MENU to reset fuel flow values to select SYSTEM SETUP and press MENU. 2.
Highlight FUEL MANAGER (Fuel Mngr) and press MENU. If the newly configured fuel flow is not shown, refresh the Bus Devices list. It, however, will appear. 3. EP-60R Fuel Flow Calibration
The factory calibration settings for the EP-60R Fuel Flow should be within 3 percent, so calibration...
Installation Configuration and Calibration Instructions - Page 14
... gallons of fuel you added when you to the main display.)
3. To calibrate a fuel flow:
7. Select the tank you refilled and press MENU. (If your Fuel Remaining Source has been set for one ...SYSTEM SETUP and press MENU.
2. Select REFILL T. and press MENU. Compare the amount of fuel, then fill up the fuel tank connected to the EP-60R Fuel Flow you will be directed to the fuel flow. Press...
Installation Configuration and Calibration Instructions - Page 15
NOTE: If you do not have the fuel remaining source set calibration back to factory default settings.
To recalibrate the fuel flow, refer to select SYSTEM SETUP and press MENU. 2. To refill tank:
1. Press MENU, use the UP and DOWN keys to the fuel flow calibration instructions in the EP-60R stays consistent with two options: Yes and No. If your unit...
Installation Configuration and Calibration Instructions - Page 17
... select SYSTEM SETUP and press MENU.
2. Highlight FUEL MNGR and press MENU.
2. The Select Engine menu will appear with up to the main display.
Select the desired Fuel Flow (FFlow) ...Rst Trip F. Reset Seasonal Fuel (Rst Seas)
The LMF-200 uses fuel flow data to set a fuel warning:
1. If you to keep a running total of fuel used for each fuel tank. The following message will...
Installation Configuration and Calibration Instructions - Page 22
... the fuel flow's location/engine on the boat to its menu will appear with Boat Setup highlighted. EP-60R Fuel Flow Configuration
You can have to measure the amount of fuel remaining in the LMF-400.
22 Press MENU, use the UP and DOWN keys to three fuel flow sensors installed on your fuel flow sensor. Press MENU, highlight SYSTEM SETUP and press ENTER.
2. Highlight FUEL SETUP and...
Installation Configuration and Calibration Instructions - Page 33
....
33 NOTE: Your unit may be used to configure an EP-60R Fuel Flow sensor.
The network devices list is located in the top half of the Bus Configuration menu. Both menus allow you access to the network. Display Unit: EP-60R Configuration & Calibration
All NMEA 2000 capable Lowrance sonar and sonar/GPS combo display units can be used to...
Installation Configuration and Calibration Instructions - Page 38
... this device's configuration? 6. The device name will be at the end of the engine connected to unconfigure your fuel flow sensor.
Unconfiguring an EP-60R Fuel Flow You can unconfigure a fuel flow by using the Restore Defaults command.
Press MENU twice, select NMEA 2000 or NETWORKING and press ENTER. A list of the page. 3. NOTE: If you execute the Restore Defaults command...
Installation Configuration and Calibration Instructions - Page 39
... and Fill Tank. The menu is divided into two parts: Tank Operations and Engine Operations. A menu will appear. 4. Adding Fuel to Tank
Tank Location, Fuel Added and Add Fuel commands work together to keep NMEA 2000 fuel data consistent with five options: Bus Setup, Fuel Management, NMEA 2000 Alarms, Waypoint Sharing and Backlight Synchronization. The Tank Location menu will appear with...
Lowrance EP-60R Fuel Flow Sensor Reviews
We have not received any reviews for Lowrance yet.