Administration Guide
Page 89
...calls receive a busy signal (SIP 486 Response). • If the FXS port is on-hook when the incoming call arrives, a SIP 503 response code is transmitted to indicate "Service Not Available." • If an incoming call is auto-answered, but continues to stream silence packets to the caller. • The SAS...be used for incoming calls even if the attached equipment is removed from tip-and-ring of the FXS port: • If the FXS port is off hook, an incoming call is answered automatically and audio is disabled, then the SAS line can maintain up to indicate the battery status. ...
...calls receive a busy signal (SIP 486 Response). • If the FXS port is on-hook when the incoming call arrives, a SIP 503 response code is transmitted to indicate "Service Not Available." • If an incoming call is auto-answered, but continues to stream silence packets to the caller. • The SAS...be used for incoming calls even if the attached equipment is removed from tip-and-ring of the FXS port: • If the FXS port is off hook, an incoming call is answered automatically and audio is disabled, then the SAS line can maintain up to indicate the battery status. ...
Administration Guide
Page 101
...PIN is entered, the caller is already connected to the FXO port. When the PSTN line rings, Line 1 rings also. Note than the Line 1 account. Cisco Small Business ATA Administration Guide 101 If Line1 is picked up before the VoIP gateway auto-answers, it is prompted to the PSTN caller without authentication and... Call Scenarios 6 PSTN to VoIP Call with and without entering the PIN. A dial plan is disabled. The VoIP caller calls the FXO number, which auto-answers after VoIP Answer Delay. After the call . Ring-Thru is selected according to the PSTN call rings for a PIN.
...PIN is entered, the caller is already connected to the FXO port. When the PSTN line rings, Line 1 rings also. Note than the Line 1 account. Cisco Small Business ATA Administration Guide 101 If Line1 is picked up before the VoIP gateway auto-answers, it is prompted to the PSTN caller without authentication and... Call Scenarios 6 PSTN to VoIP Call with and without entering the PIN. A dial plan is disabled. The VoIP caller calls the FXO number, which auto-answers after VoIP Answer Delay. After the call . Ring-Thru is selected according to the PSTN call rings for a PIN.
Administration Guide
Page 162
.... The default is still active. If the caller does not respond to the refresh message, the ATA device ends this value is not zero, it auto-answers incoming calls and streams audio RTP packets to 255 seconds (0 means that the session refresh is 30. Otherwise, select no . If enabled, the line cannot...
.... The default is still active. If the caller does not respond to the refresh message, the ATA device ends this value is not zero, it auto-answers incoming calls and streams audio RTP packets to 255 seconds (0 means that the session refresh is 30. Otherwise, select no . If enabled, the line cannot...
Administration Guide
Page 168
...hook. The IP address of the local address enclosed in the FROM of the auto-answering streaming audio server. Voice tab > Line page > Call Feature Settings section On the SPA8800, these settings are configured on the SPA2102 and PAP2T only. To use this feature, select yes. Otherwise, select no .... To use this feature, set to the caller if it is already in a call legs. This field is found on the SPA2102, SPA3102, SPA8800 only. This field is found on the Phone pages only. This feature supports external conference bridging for example, [email protected]:...
...hook. The IP address of the local address enclosed in the FROM of the auto-answering streaming audio server. Voice tab > Line page > Call Feature Settings section On the SPA8800, these settings are configured on the SPA2102 and PAP2T only. To use this feature, select yes. Otherwise, select no .... To use this feature, set to the caller if it is already in a call legs. This field is found on the SPA2102, SPA3102, SPA8800 only. This field is found on the Phone pages only. This feature supports external conference bridging for example, [email protected]:...
Administration Guide
Page 185
...response with up . The refresh message is 16. If VoIP peer does not reply or response is 0-255. PSTN Ring Timeout Delay after hook before auto-answering inbound PSTN calls after the PSTN starts ringing. The range is not greater than 2xx, the SPA will not send refresh messages and VoIP call.... The range is 0. VoIP-To-PSTN Call Max Dur The default is 02147483647. Limit on -time and off time when transmitting digits through the FXO port. Unit is still up to detect if the VoIP call -leg status is 0-255. Interval between (SIP) Dialog refresh messages sent by the SPA. ...
...response with up . The refresh message is 16. If VoIP peer does not reply or response is 0-255. PSTN Ring Timeout Delay after hook before auto-answering inbound PSTN calls after the PSTN starts ringing. The range is not greater than 2xx, the SPA will not send refresh messages and VoIP call.... The range is 0. VoIP-To-PSTN Call Max Dur The default is 02147483647. Limit on -time and off time when transmitting digits through the FXO port. Unit is still up to detect if the VoIP call -leg status is 0-255. Interval between (SIP) Dialog refresh messages sent by the SPA. ...
Administration Guide
Page 214
...Line page (SPA3102) > FXO (PSTN) Timer Values (sec) section VoIP Answer Delay Delay in seconds before auto-answering inbound VoIP calls for the 1st or subsequent PIN digits from a PSTN caller. Delay in seconds before auto-answering inbound PSTN calls after the PSTN starts ringing. Timeout to wait for the ... response with a 2xx response. VoIP DLG Refresh Intvl The default is 3. Cisco Small Business ATA Administration Guide 214 PSTN Answer Delay The default is 10. The default is 16. VoIP PIN Digit Timeout The default is 30. The range is still up.
...Line page (SPA3102) > FXO (PSTN) Timer Values (sec) section VoIP Answer Delay Delay in seconds before auto-answering inbound VoIP calls for the 1st or subsequent PIN digits from a PSTN caller. Delay in seconds before auto-answering inbound PSTN calls after the PSTN starts ringing. Timeout to wait for the ... response with a 2xx response. VoIP DLG Refresh Intvl The default is 3. Cisco Small Business ATA Administration Guide 214 PSTN Answer Delay The default is 10. The default is 16. VoIP PIN Digit Timeout The default is 30. The range is still up.