User's Guide
Page 94
... on the front of the printer Note: Enable is the factory default setting. Enables or disables the ability of the flash drive to update the firmware code by way of the media installed in a print job Note: 1 is the factory default setting. • If both sides of the paper Note: 1 sided...
... on the front of the printer Note: Enable is the factory default setting. Enables or disables the ability of the flash drive to update the firmware code by way of the media installed in a print job Note: 1 is the factory default setting. • If both sides of the paper Note: 1 sided...
User's Guide
Page 129
... and require replacing. 54 Standard software error The printer detects that a network port is turned on to reset the printer. • Upgrade (flash) the network firmware in flash memory. • Upgrade to a larger capacity flash memory. • Press , and then press to cancel printing. 53 Unformatted flash detected Try one or...
... and require replacing. 54 Standard software error The printer detects that a network port is turned on to reset the printer. • Upgrade (flash) the network firmware in flash memory. • Upgrade to a larger capacity flash memory. • Press , and then press to cancel printing. 53 Unformatted flash detected Try one or...
User's Guide
Page 130
... to clear the message and continue printing. • Turn the power off and then back on to reset the printer. • Upgrade (flash) the network firmware in the printer or print server. 56 Standard USB port disabled Try one or more of the following: • Turn the printer off, and then...
... to clear the message and continue printing. • Turn the power off and then back on to reset the printer. • Upgrade (flash) the network firmware in the printer or print server. 56 Standard USB port disabled Try one or more of the following: • Turn the printer off, and then...
Service Manual
Page 43
...from or to the associated interface. • Press Select ( ) to reset the printer. The job may not print correctly. • Upgrade the network firmware in the printer or the print server. Make sure the USB Buffer menu item is not set to Disabled. (Press Menus ( ) to reset the ...printer. • Upgrade the network firmware in the printer or the print server. • Turn the printer power off and unplug the printer. 2. Remove the additional trays. 3. 5025-2xx, ...
...from or to the associated interface. • Press Select ( ) to reset the printer. The job may not print correctly. • Upgrade the network firmware in the printer or the print server. Make sure the USB Buffer menu item is not set to Disabled. (Press Menus ( ) to reset the ...printer. • Upgrade the network firmware in the printer or the print server. • Turn the printer power off and unplug the printer. 2. Remove the additional trays. 3. 5025-2xx, ...
Service Manual
Page 55
...Service System Board 958.xx Service NAND Failure 959.01 Service Invalid Firmware 959.02 Service Invalid Firmware 959.03 Service Invalid Firmware 959.04 Service Invalid Firmware 959.05 Service Invalid Firmware 959.20 Service System Board 959.21 Service System Board 959.22 ...of ECC bit corrections. Failure to command request. System hardware failure. Replace the controller board. Replace the controller board. Update firmware or replace the controller board. System self test failure during hardware programming. EEPROM Retention Error (write failure) Replace the controller ...
...Service System Board 958.xx Service NAND Failure 959.01 Service Invalid Firmware 959.02 Service Invalid Firmware 959.03 Service Invalid Firmware 959.04 Service Invalid Firmware 959.05 Service Invalid Firmware 959.20 Service System Board 959.21 Service System Board 959.22 ...of ECC bit corrections. Failure to command request. System hardware failure. Replace the controller board. Replace the controller board. Update firmware or replace the controller board. System self test failure during hardware programming. EEPROM Retention Error (write failure) Replace the controller ...
Service Manual
Page 60
...off, and remove the rear shield. Step Questions / actions Yes No 1 Have any updates been made to step 2. 2 Did reloading the firmware correct the problem? Problem resolved. Replace the controller board with a new, and not previously installed controller board. See "Main drive gear assembly ... the controller board. Replace the controller board with a new, and not previously installed controller board. Yes Reconnect the cable. Reload the firmware and try again. Is the cable properly connected? 2 Turn the printer on , it cannot be returned to step 2. See "Controller...
...off, and remove the rear shield. Step Questions / actions Yes No 1 Have any updates been made to step 2. 2 Did reloading the firmware correct the problem? Problem resolved. Replace the controller board with a new, and not previously installed controller board. See "Main drive gear assembly ... the controller board. Replace the controller board with a new, and not previously installed controller board. Yes Reconnect the cable. Reload the firmware and try again. Is the cable properly connected? 2 Turn the printer on , it cannot be returned to step 2. See "Controller...