Instruction Manual
Page 5
... spacer on the panel and then mark the hole positions. 3. Determiner la position de montage en se referant aux instructions intitulees "Emplacements de montage". 2. Retirez Ia feuille de protection placee sur la bande...den Abstandshalter an der Ruckseite des Lautsprecherflansches so anbringen, daB der Flansch vollstandig bedeckt ist. 5. Das Gerat einbauen, wie in Fig. 3. Place the supplied template on the back of the speaker flange so that the flange is completely covered. 5. Install the unit as shown in Abb. 3 dargestellt. ■ KFC-W3005 KFC-W2505 KFC-W2005 ■ KFC-W2005G W1705...
... spacer on the panel and then mark the hole positions. 3. Determiner la position de montage en se referant aux instructions intitulees "Emplacements de montage". 2. Retirez Ia feuille de protection placee sur la bande...den Abstandshalter an der Ruckseite des Lautsprecherflansches so anbringen, daB der Flansch vollstandig bedeckt ist. 5. Das Gerat einbauen, wie in Fig. 3. Place the supplied template on the back of the speaker flange so that the flange is completely covered. 5. Install the unit as shown in Abb. 3 dargestellt. ■ KFC-W3005 KFC-W2505 KFC-W2005 ■ KFC-W2005G W1705...
Instruction Manual
Page 6
...wiring of this unit away from motors, high-voltage leads and other possible noise sources. • To prevent a short-circuit, keep all wiring away from moving parts, sharp edges, cut metal, etc. • Do not switch ON the power until wiring is completed. ■ Tools required for installation... • Eye protectors (for mounting and where is enough space for eye protection when using the electric hand drill) • Electrical tape ■ Mounting locations This unit can be installed in the boot (trunk), on the rear deck (only KFC-W2OO5G/W1705), or in separate enclosures. Avant...
...wiring of this unit away from motors, high-voltage leads and other possible noise sources. • To prevent a short-circuit, keep all wiring away from moving parts, sharp edges, cut metal, etc. • Do not switch ON the power until wiring is completed. ■ Tools required for installation... • Eye protectors (for mounting and where is enough space for eye protection when using the electric hand drill) • Electrical tape ■ Mounting locations This unit can be installed in the boot (trunk), on the rear deck (only KFC-W2OO5G/W1705), or in separate enclosures. Avant...
Instruction Manual
Page 12
...specifications SYMBOL UNIT KFC-W3005 MODEL NAME KFC-W2505 KFC-W2005 /W2005G KFC-W1705 Nominal Impedance Z Ohm 4 4 4 4 DC Resistance Revc Ohm 3.34 3.39 3.35 3.10 Voice Coil Inductance Levc mH 1.10 0.90 0.64 0.70 Piston Area Force Factor Sd sqm BL Tm 0.0491 9.80 0.0347 ti 7.57 0.0206 8.07 0.0125 5.60 Volume... Q Factor Qts 0.66 0.83 1.04 0.94 Peak Power W Watts 700 600 500 260 Peak Excursion Xmax mm 9 12 6.5 2.5 Displacement cc 3,980 2,280 1,520 750 cu•ft 0.141 0.080 0.054 0.026 Mounting Depth mm (in.) 135(5-5/16) 115(4-1/2) 100(3-15/16...
...specifications SYMBOL UNIT KFC-W3005 MODEL NAME KFC-W2505 KFC-W2005 /W2005G KFC-W1705 Nominal Impedance Z Ohm 4 4 4 4 DC Resistance Revc Ohm 3.34 3.39 3.35 3.10 Voice Coil Inductance Levc mH 1.10 0.90 0.64 0.70 Piston Area Force Factor Sd sqm BL Tm 0.0491 9.80 0.0347 ti 7.57 0.0206 8.07 0.0125 5.60 Volume... Q Factor Qts 0.66 0.83 1.04 0.94 Peak Power W Watts 700 600 500 260 Peak Excursion Xmax mm 9 12 6.5 2.5 Displacement cc 3,980 2,280 1,520 750 cu•ft 0.141 0.080 0.054 0.026 Mounting Depth mm (in.) 135(5-5/16) 115(4-1/2) 100(3-15/16...