Instruction Manual
Page 4
... not operate normally after a while, consult your unit If this unit or the connected unit (auto disc changer, etc.) fails to reset your Kenwood dealer. Refer to (page 28) for the condensation to explain more clearly how the controls are examples used to evaporate. This unit ... can be inapplicable. 4 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Wiping the faceplate with a clean soft dry cloth. In such a situation, remove the disc and wait for the details of the status display. • The illustrations of the unit and faceplate with your Kenwood dealer to the unit may scratch...
... not operate normally after a while, consult your unit If this unit or the connected unit (auto disc changer, etc.) fails to reset your Kenwood dealer. Refer to (page 28) for the condensation to explain more clearly how the controls are examples used to evaporate. This unit ... can be inapplicable. 4 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Wiping the faceplate with a clean soft dry cloth. In such a situation, remove the disc and wait for the details of the status display. • The illustrations of the unit and faceplate with your Kenwood dealer to the unit may scratch...
Instruction Manual
Page 44
...(page 42) - X'Over Setting (page 44) - Select "YES". Adjust each item. Audio Preset Memory Registering the value setup by the Reset button. • This function cannot be registered when the iPod Equalizer set in the section (page 42). DSP Setup X'Over Setting Fine adjusting... press it when the desired item is displayed. Press the [VOL] button. 6 Repeat steps 3 to 4 to put in (page 39). 44 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Car Type Fine Adjustments (page 43) - Manual Equalizer Control (page 39) - Select "Detailed Setup" > "Preset" > "Memory". 3 Select ...
...(page 42) - X'Over Setting (page 44) - Select "YES". Adjust each item. Audio Preset Memory Registering the value setup by the Reset button. • This function cannot be registered when the iPod Equalizer set in the section (page 42). DSP Setup X'Over Setting Fine adjusting... press it when the desired item is displayed. Press the [VOL] button. 6 Repeat steps 3 to 4 to put in (page 39). 44 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U Car Type Fine Adjustments (page 43) - Manual Equalizer Control (page 39) - Select "Detailed Setup" > "Preset" > "Memory". 3 Select ...
Instruction Manual
Page 46
...Memory. Turn the [VOL] knob and press it when the desired item is displayed. Select preset number. " FAV " is displayed. 46 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U The memory cannot be automatically played. Select preset number. Select "ALL" if you want to delete all. 6 Turn the [VOL] knob...knob. 5 Select the number you want to recall in the memory Press the [VOL] knob. Songs will not be erased by the Reset button. In this unit becomes different from that in the first hierarchy can be registered. Retrieving an item registered to Favorite. 1 Enter ...
...Memory. Turn the [VOL] knob and press it when the desired item is displayed. Select preset number. " FAV " is displayed. 46 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U The memory cannot be automatically played. Select preset number. Select "ALL" if you want to delete all. 6 Turn the [VOL] knob...knob. 5 Select the number you want to recall in the memory Press the [VOL] knob. Songs will not be erased by the Reset button. In this unit becomes different from that in the first hierarchy can be registered. Retrieving an item registered to Favorite. 1 Enter ...
Instruction Manual
Page 69
... you may cause a short circuit, that in the following : • Communicate with too much dust or the possibility of KDC-X994/ KDC-BT945U Installation Procedure 1 To prevent a short circuit, remove the key from the ignition and disconnect the - The above maximum ... 5* ..........4 3 m (9.5 ft) ..........1 *Accessory of water splashing. • Do not use your car's ignition does not have been activated. battery. 8 Press the reset button. 2WARNING If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you connect the + connector of 10...
... you may cause a short circuit, that in the following : • Communicate with too much dust or the possibility of KDC-X994/ KDC-BT945U Installation Procedure 1 To prevent a short circuit, remove the key from the ignition and disconnect the - The above maximum ... 5* ..........4 3 m (9.5 ft) ..........1 *Accessory of water splashing. • Do not use your car's ignition does not have been activated. battery. 8 Press the reset button. 2WARNING If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you connect the + connector of 10...
Instruction Manual
Page 74
...ERROR 77/Mecha Error: The unit is scratched a lot. Or the unit is specified in the Instruction Manual for some reason. Press the reset button on the unit. The Bluetooth audio player cannot be registered (pairing). The PIN code is fixed. When a PIN code is... connected USB device is not the one who registered the voice tag can be ejected or the display continues to USB again. 74 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U The CD is heard from the rear speakers. You are talking in the Instruction Manual, try "0000". ? No sound...
...ERROR 77/Mecha Error: The unit is scratched a lot. Or the unit is specified in the Instruction Manual for some reason. Press the reset button on the unit. The Bluetooth audio player cannot be registered (pairing). The PIN code is fixed. When a PIN code is... connected USB device is not the one who registered the voice tag can be ejected or the display continues to USB again. 74 | KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U The CD is heard from the rear speakers. You are talking in the Instruction Manual, try "0000". ? No sound...
Instruction Manual
Page 75
... to Favorite Preset Memory No Access: The procedure preset with Favorite Control cannot be available. If this message still appears, press the reset button on again. No more Bluetooth device cannot be connected to the iPod has failed. Remove the USB device and then...has not been registered (pairing). HF Error 07: The memory cannot be recalled depending on again. If this message still appears, press the reset button on supported iPods. Un Known: The Bluetooth device cannot be recognized. Device Full: 5 Bluetooth device have occurred to the connected USB ...
... to Favorite Preset Memory No Access: The procedure preset with Favorite Control cannot be available. If this message still appears, press the reset button on again. No more Bluetooth device cannot be connected to the iPod has failed. Remove the USB device and then...has not been registered (pairing). HF Error 07: The memory cannot be recalled depending on again. If this message still appears, press the reset button on supported iPods. Un Known: The Bluetooth device cannot be recognized. Device Full: 5 Bluetooth device have occurred to the connected USB ...