Instruction Manual
Page 4
.... • Do not use the wrong screws, you use your unit to malfunction. • To prevent a short circuit when replacing a fuse, first disconnect the wiring harness. • Do not place any metallic objects (such as it may fall out of water splashing. • Do not set the removed faceplate or the...or metal tools) inside the unit. • If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer. • Make sure not to get your fingers caught between the faceplate and the unit. • Do not apply excessive force to the ...
.... • Do not use the wrong screws, you use your unit to malfunction. • To prevent a short circuit when replacing a fuse, first disconnect the wiring harness. • Do not place any metallic objects (such as it may fall out of water splashing. • Do not set the removed faceplate or the...or metal tools) inside the unit. • If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer. • Make sure not to get your fingers caught between the faceplate and the unit. • Do not apply excessive force to the ...
Instruction Manual
Page 32
... to the terminals to cause a short circuit, then replace the old fuse with one with the same rating. • Insulate unconnected wires with the ignition key. Connect the wiring harness connector to a front output terminal, do not mix front and rear). Accessories/ Installation Procedure Accessories 1 2 3 4 5 ..........1 ..........2 ...• If the fuse blows, first make sure to both the rear output terminals (do not connect the - Connect the wiring harness wires in the car. • When only two speakers are working properly. • Mount the unit so that can be damaged...
... to the terminals to cause a short circuit, then replace the old fuse with one with the same rating. • Insulate unconnected wires with the ignition key. Connect the wiring harness connector to a front output terminal, do not mix front and rear). Accessories/ Installation Procedure Accessories 1 2 3 4 5 ..........1 ..........2 ...• If the fuse blows, first make sure to both the rear output terminals (do not connect the - Connect the wiring harness wires in the car. • When only two speakers are working properly. • Mount the unit so that can be damaged...
Instruction Manual
Page 33
... left output (White) (KDC-X679 only) Rear left output (White) / Sub Woofer left output (White) (KDC-MP625/MP6025 only) Rear right output (Red) / Sub Woofer right output (Red) (KDC-MP625/MP6025 only) FM/AM antenna input KENWOOD disc changer input To connect the Disc changer, consult your Disc changer manual. Battery wire (Yellow) Ground wire (Black) - (To...
... left output (White) (KDC-X679 only) Rear left output (White) / Sub Woofer left output (White) (KDC-MP625/MP6025 only) Rear right output (Red) / Sub Woofer right output (Red) (KDC-MP625/MP6025 only) FM/AM antenna input KENWOOD disc changer input To connect the Disc changer, consult your Disc changer manual. Battery wire (Yellow) Ground wire (Black) - (To...
Instruction Manual
Page 37
...in the car. ☞ Check the speaker wiring. ✔ The speakers are not wired correctly. ☞ Reconnect the speaker wires so that can be entered with one side. ☞ Center the fader and balance settings. ✔ The input/output wires or wiring harness are set all the way. ✔ ...be heard, or the volume is low. ✔ The fader or balance settings are connected incorrectly. ☞ Reconnect the input/output wires or the wiring harness correctly. The sound quality is poor or distorted. ✔ One of the car. ? Before calling service, first check the following ...
...in the car. ☞ Check the speaker wiring. ✔ The speakers are not wired correctly. ☞ Reconnect the speaker wires so that can be entered with one side. ☞ Center the fader and balance settings. ✔ The input/output wires or wiring harness are set all the way. ✔ ...be heard, or the volume is low. ✔ The fader or balance settings are connected incorrectly. ☞ Reconnect the input/output wires or the wiring harness correctly. The sound quality is poor or distorted. ✔ One of the car. ? Before calling service, first check the following ...