JET Tools VBS-1408 Support and Manuals
Get Help and Manuals for this JET Tools item
This item is in your list!
View All Support Options Below
Free JET Tools VBS-1408 manuals!
Problems with JET Tools VBS-1408?
Ask a Question
Free JET Tools VBS-1408 manuals!
Problems with JET Tools VBS-1408?
Ask a Question
Popular JET Tools VBS-1408 Manual Pages
User Manual - Page 1
M-414483 Revision G2 10/2014 Copyright © 2014 JET This .pdf document is bookmarked
Operating Instructions and Parts Manual
14-inch Metalworking Band Saw
Model VBS-1408
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.waltermeier.com
Part No.
User Manual - Page 2
... be asked to become inoperable within a
reasonable amount of use the Service Center Locator on official JET website are given as expendable parts or accessories expected to provide proof of our tools needs service or repair, please contact Technical Service by a 90 day limited warranty against manufacturers' defects.
The specifications listed in your local distributor or visit the...
User Manual - Page 3
...15 14.0 Maintenance...15 14.1 Lubrication schedule ...15 15.0 Troubleshooting ...16 15.1 Operating problems...16 15.2 Mechanical and electrical problems ...17 15.3 Welded blade inspection ...18 15.4 Welder mechanical problems ...19 16.0 Speed and pitch chart ...20 17.0 Typical Band Saw Operations ...21 18.0 Replacement Parts...21 18.1.1 VBS-1408 Band Saw - Parts List...24 19.0 Electrical diagram...
User Manual - Page 4
...repaired or replaced... the blade or other part that ...JET disclaims any real or implied warranty and holds itself harmless from chemically treated lumber. Give your workshop child proof with all loose clothing and confine long hair. Use the right tool...specifically designed to the power supply.
12. improper accessories may cause serious injury.
3. Read and understand the entire owner's manual...
User Manual - Page 5
...manual
This manual is performed on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. Follow instructions for the best and safest performance. Use a brush or compressed air to a complete stop.
29. Turn the power off and blade has stopped moving.
33. Always use power tools...result in this manual for a JET Model VBS-1408 Band Saw....
User Manual - Page 6
...deg. 5.0 Specifications
Model number ...VBS-1610 Stock number ...414485 Blade speed ...variable...Blade width, maximum ...1/2" Overall height ...68-1/2" Floor space required ...34" x 24" Weights: Net...580 lb Shipping ...685 lb
The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications...
User Manual - Page 7
... repairs must be done with additional shims, as these changes to side. The VBS-1408 ...damage has occurred during shipping.
2. Figure 1
7.0 Installation
1. To level the machine, place a machinist's level...on the circuit board. The band saw .
Replace the 115V plug with the saw must be ...be bolted to blade, both directions.
5. If necessary, adjust the pointers to blade in place....
User Manual - Page 12
Set pressure selector switch (counterclockwise rotation) to overheat.
1. Clean welder jaws and lower jaw inserts.
2. NOTE: There will contact welder jaws. Position back edge of blade against the other ). Tighten right clamp.
6. Remove any problems. Make corrections before blade can be uniformly spaced. Tighten left clamp.
Unclamp blade.
9. Simultaneously, sparks ...
User Manual - Page 14
... flash or "stub" teeth which project beyond the normal set or height of specific blades on lower alloy ferrous materials.
1.
When the saw has completed about 1/3 of round stock.
2. The blade is NOT running . While machine is now considered ready for identification of JET-supplied blades on specific materials. Preventing shorts or poor electrical contact. Turning handwheel...
User Manual - Page 16
... replace blade. Feed rate excessive. Use proper width blade for short radius cutting. Guide post too high. Blade warps.
See section 10.3 Select narrower blade appropriate to workpiece. Inadequate blade tension. Feeding workpiece too forcefully. Blade too wide for radius or wavy line cutting. Increase tension. 15.0 Troubleshooting
15.1 Operating problems
Table 1
Trouble
Probable...
User Manual - Page 17
... problems
Table 2
Trouble
Machine...problem. Replace with adequate size and length cord. Motor overheated. If problem persists, check amp setting... on the overload relay. Match the full load amps on the motor as noted on the circuit breaker built into the blade. If you have a motor problem. If incoming voltage is suspect, you have a power supply problem...
User Manual - Page 19
... not run when Grinder switch is pushed.
Blade ends have rust.
Grinder switch is pushed.
Replace grinder switch.
19 Blade has oil on rear side of order, or decayed. Weld area melts when weld switch is bad.
Grinder motor is poor; 15.4 Welder mechanical problems
Table 4
Trouble
Weld could not be tightly clamped with a file...
User Manual - Page 21
Having the Model Number and Serial Number of your machine available when you call 1800-274-6848 Monday through Friday (see our website for business hours, www.jettools.com). 17.0 Typical Band Saw Operations
Figure 17
18.0 Replacement Parts
Replacement parts are listed on the following pages. To order parts or reach our service department, call will allow...
User Manual - Page 24
... ..........1960 Upper Blade (re: VBS1610-BS 1 1970 ..........1970 Plate (re: VBS1610-BS 1 1980 .......... 1980 Joint (re: VBS1610-BS 1 1990 ..........1990 Handle Bar (re: VBS1610-BS 1 2000 ..........VBS14-009 Drive Motor ...1 2010 ..........VBS1408-2010.......... 18.1.3 VBS-1408 Band Saw - Upper Wheel 1 3060 ..........VBS1408-3060.......... Parts List
Index No Part No
Description...
JET Tools VBS-1408 Reviews
Do you have an experience with the JET Tools VBS-1408 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for JET Tools yet.
Earn 750 points for your review!