JET Tools JG-300A Support and Manuals
Get Help and Manuals for this JET Tools item
This item is in your list!
View All Support Options Below
Free JET Tools JG-300A manuals!
Problems with JET Tools JG-300A?
Ask a Question
Free JET Tools JG-300A manuals!
Problems with JET Tools JG-300A?
Ask a Question
Popular JET Tools JG-300A Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
3/4, 1-1/2, and 3 Ton Grip Pullers
Models JG-75A, JG-150A, JG-300A
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Model JG-75A shown
Part No. M-286575 Revision A2 04/2014 Copyright © 2014 JET
User Manual - Page 2
... of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to -date product information, check with your product or on official JET website are not binding. Machine Accessories; Heavy-Duty Air Tools;
Please note that are covered by calling 1-800-274-6846. Limitations on the JET website. The specifications listed in...
User Manual - Page 3
... Do not use this tool while tired or under the puller. 9. Do not use handle extensions (cheaters). 5. Failure to comply with this device must provide adequate support to lift vertically, make sure hook is damaged or malfunctioning. 7. Table of Contents
Warranty and Service ...2 Warning...3 Introduction ...4 Specifications ...4 Replacement Parts ...4 Unpacking ...5
Contents of the...
User Manual - Page 4
... are listed on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown.
Having the Model Number and Serial Number of trouble free operation if used in accordance with the grip puller, add a "K" to serve you quickly and accurately.
4 Specifications
Stock Number 286575 286515 286530 Model Number JG-75A JG-150A JG-300A Pulling Capacity...
User Manual - Page 5
... 1
FEATURES OF THE GRIP PULLER (1-1/2 ton model shown)
Assembly and Set-Up
Pre-Lubrication
Before proceeding with the following parts list to the fastening bolt on the puller body.
5
Figure 2 Missing parts, if any damage immediately to internal parts. Read the instruction manual thoroughly for shipping damage. Use special care to install the cotter pin through the fastening...
User Manual - Page 6
...on the lever.
8. IMPORTANT: A shear pin (#25 in the parts list) is not obstructed.
6. If the load being handled is too...the slack and make sure that the exit point is installed in the middle of higher pulling capacity. Insert the end...is easily replaced using one of the 3/4ton puller.
6
Figure 3 Figure 4 Figure 5 Figure 6
See Figure 5.
2. To send the wire rope forward, set the ...
User Manual - Page 7
...basket-like a basket or is not in proper position. Use care to engaged position.
Replace the wire rope immediately if:
• The thickness of the rope becomes less than ...setting the clamp lever into the notch (disengage the clamp, then pulling the wire rope from rain, dew, high humidity areas or around acidic chemicals, which will not move in failure.
Troubleshooting
Trouble...
User Manual - Page 9
Part No.
Parts List: JG-75A (3/4 Ton Grip Puller)
Index No. Description
Size
Qty
1 JG75A-1 Case, Right 1 2 TS-2285121 Flat Head Screw M5x12 1 3...Assembly 1 25 JG75A-8 Shear Pin 1 26 JG75A-26 Axle...2 27 JG75A-27 Front Slide Assembly 1 28 JG75A-28 Spring Guide 2 29 JG75A-29 Spring...2 30 JG75A-30 Bottom Clamp 2 31 JG75A-31 Top Clamp 2 32 JG75A-32 Back Slide ...
User Manual - Page 11
...Socket Head Cap Screw M6x55 6 12 JG75A-12 Square Nut M6 6 13 JG75A-13 Cotter Pin Assembly 1 14 JG150A-14 Wire Rope Guide Sleeve 1 15 JG150A-15 Release Lever 1 16 JG150A-16 Push Link, Left 1 17 JG150A-17 Push Link, Right 1 18 ... Hook 1 JG75A-WL Warning Label (not shown 1 286514 1-1/2T Wire Rope, 66 Ft. (not shown 1
11 Parts List: JG-150A (1-1/2 Ton Grip Puller)
Index No...
User Manual - Page 13
Parts List: JG-300A (3 Ton Grip Puller)
Index No. Description
Size
Qty
1 JG300A-1 Case, Right 1 2 JG300A-2 Flat Head Screw M5x8 1 3 JG75A-3 Washer 1 4 JG300A-4 Case, Left 1 5 JG300A-5 Name Plate 1 6 JG75A-6 Rivet M2x6 4 7 JG300A-7 Fastening Bolt Assembly 1 8 JG300A-8 Shear Pin 5 9 JG150A-9 Telescopic Handle 1 10 TS-1551061 Lock Washer M8 6 11 TS-1504131 ...
JET Tools JG-300A Reviews
Do you have an experience with the JET Tools JG-300A that you would like to share?
Earn 750 points for your review!
We have not received any reviews for JET Tools yet.
Earn 750 points for your review!