JET Tools J-7040 Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools J-7040 manuals!
Problems with JET Tools J-7040?
Ask a Question
Free JET Tools J-7040 manuals!
Problems with JET Tools J-7040?
Ask a Question
Popular JET Tools J-7040 Manual Pages
User Manual - Page 1
M-414472 Revision C2 03/2014 Copyright © 2014 JET This .pdf document is bookmarked
Operating Instructions and Parts Manual
10" x 16" Horizontal Band Saw
Models J-7020, J-7040
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No.
User Manual - Page 2
... FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED. JET SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. Parts; Metalworking Machinery; Shop Tools; How to Get Technical Support Please contact Technical Service by calling 1-800-274-6846, 8AM...
User Manual - Page 3
three phase only (model J-7040 29
3 2.0 Table of contents
Section
Page
1.0 Warranty and Service...2 2.0 Table of contents...3 3.0 Safety Warnings...4 4.0 About this machine and manual ...6 5.0 Specifications ...6 6.0 Machine setup ...8
6.1 Uncrating and spotting ...8 7.0 Electrical connections ...8 8.0 Operating instructions ...8
8.1 Controls ...8 8.2 Setting blade speed...8 8.3 Raising/...
User Manual - Page 4
... makeshift repairs done to the floor.
12. Read, understand and follow the instructions in the operator's and parts manual which was not designed.
17.
When using the machine in the machine. Always follow the instructions in the operators and parts manual when changing accessory tools or parts.
- It is mandatory that the start switch in the "OFF" position before servicing...
User Manual - Page 5
...free of blade support mechanism is done, or before any attempt is started and you are recommended.
11. Eyewear shall be securely clamped before any periodic service or maintenance is... not comply with the National Electrical Code and local codes and ordinances. Know the tool you should be grounded in accordance with ANSI Z87.1 specifications could result in order to deliver ample...
User Manual - Page 6
...the instructions as set forth in this manual before attempting assembly or operation! Your machine has been designed and constructed to the blade. Failure to local/national electrical codes
6 The blade guide system has adjustable six-point contact using a combination of this document. p/min
1 subject to comply may cause serious injury!
5.0 Specifications
Model number J-7020 J-7040...
User Manual - Page 7
...specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications...)
(1931x762x1170mm)
(1931x762x1170mm)
Materials: Bed and motor support cast iron cast iron cast iron Blade wheels cast iron ...steel steel Stand steel steel steel Blade guides carbide blocks/ball bearing .... carbide blocks...
User Manual - Page 8
... panel. 6.0 Machine setup
The saw delivered to you are installing the motor power cord...head (see figure 2).
8.2 Setting blade speed
1. It is ... downward and put the saw (model J-7040) on the top, rear of...off work on a pivoting tube. JET recommends that the fuses have been... codes take precedence over recommendations.
8.0 Operating instructions
8.1 Controls
The operating controls for service....
User Manual - Page 9
... of the adjustment mechanism. For example, to set about midway between the saw base and the saw head in the downward direction. To lower the saw head will move downward. To lower the saw head with power off , pull and turn the red knob (manual override) on the electro-magnetic valve (see...
User Manual - Page 10
... provide support at its...JET.
For very high production on cutting of special materials, or to cut hard-to complete the cut materials such as stainless steel, tool steel, or titanium, you with a very light feed rate.
3. Set...service.
9.0 Work setup
9.1 Securing workpiece for many shop cutting needs, do not encompass the wide variety of blades of the cut with very specific instructions...
User Manual - Page 13
...The
4.
Shut off the drive wheel. Install the two blade guide bearing brackets.
If the blade is always better to... a new blade does not correct the problem, check the blade guides for proper spacing. Position the guides so the bearings just touch the blade.... until the paper is poor. Tighten all four knobs. Set the clearance at approximately 0.001 inch.
13 Repeat the ...
User Manual - Page 15
... a year.
10. Install the left blade guide support. Adjust tracking as required (see exploded figure, section 14.2.1).
8. Set the arm at the ...the coolant supplier's instructions for change frequency.
11. Check the guide bearings and the carbide guides to sect. ...the blade.
8. Put the replacement belt in back of saw head support and through the motor support bracket.
8. Remove the knob...
User Manual - Page 16
... the keyway in the speed reducer shaft. Reinstall the wheel on the idler shaft.
7. Install the blade (see sect. 12.3, Changing blades).
2. Install the bearing in the end of the speed reducer shaft.
7. The blade guide supports allow you to set to just clear the workpiece to be cut -off the power to the branch...
User Manual - Page 17
...the spring washer onto the capscrew and re-install into guide support.
2.
Install bushing in the guide support until the bearing contacts the blade.
12.12 Replacing blade edge bearings
1. Install cap screw through bushing and into the floating block.
3. Figure 18: Blade edge bearing replacement
12.13 Replacing wire brush
1. Install replacement brush and secure with four knobs. Using...
User Manual - Page 19
.... Adjust blade guide bearings.
reduce feed pressure. Blade tooth pitch too coarse for business hours, www.jettools.com). feed too fast. Blade too fine for workpiece (especially with heavier, soft material). Coolant level too low. Replace pump. V-belt is loose.
Use blade with finer tooth pitch. To order parts or reach our service department...
JET Tools J-7040 Reviews
We have not received any reviews for JET Tools yet.