JET Tools JJP-8BT Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools JJP-8BT manuals!
Problems with JET Tools JJP-8BT?
Ask a Question
Free JET Tools JJP-8BT manuals!
Problems with JET Tools JJP-8BT?
Ask a Question
Popular JET Tools JJP-8BT Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
8-inch Jointer-Planer
Model JJP-8BT
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No. M-707400 Revision B 08/2014 Copyright © 2014 JET
User Manual - Page 2
... explain and assist with Warranty Period 90 Days - JET® branded products are not binding. Parts; Metalworking Machinery; Manual Hoists; Manual Hoist Accessories; Who is Covered This warranty covers only the initial purchaser of the product from the date of our tools needs service or repair, please contact Technical Service by JPW Industries, Inc. The exceptions are acrylics...
User Manual - Page 3
Planer/Jointer 22
17.0 Replacement Parts...22
17.1.1 Jointer/Planer - JJP-8BT...36
3 Planer 21
16.3 Mechanical Troubleshooting - Exploded View 35
18.0 Electrical Connections - Jointer 20
16.2 Performance Troubleshooting - Parts List ...23
17.1.2 Assembly Drawing Index...27
17.1.3 Planer Table Assembly ...28
17.1.4 Motor Assembly...29
17.1.5 Front Frame Assembly ...29
...
User Manual - Page 5
...tool or attachment to do a job for stock condition and grain orientation.
36. Maintain tools with a smooth, even motion. Follow instructions... used in this for other purposes, JET disclaims any real or implied warranty and... to plane against the cutterhead or other moving parts. To avoid kickback, the grain must be ... machine damage. Do not use this manual:
This means that if precautions are ...
User Manual - Page 6
...to comply may cause serious injury!
4.0 Features
Features
5.0 Specifications
Model number ...JJP-8BT Stock number ...707400 Cutterhead speed...9000rpm Number of knives ...2 ... of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations.
6 Read and understand the entire contents of this manual were current at time...
User Manual - Page 7
... packing material until your Model JJP-8BT Jointer-Planer is assembled and is your key for identifying the parts used throughout the Assembly section for easy reference.
The letter identification in the list corresponds to 4" Hose Adapter - F 01 Owner's Manual - H 01 Warranty Card (not shown)
Knobs and Handles 01 Lock Knob (p/n JJP8BT-90L) - M 01 Lock Handle...
User Manual - Page 8
... Hardware Package)
8 The following instructions are included if you have purchased the stand or will purchase one at the phone number on the cover of this manual. SK 04 Socket Head Cap Screw, M8x20 (#16, Stand
Assbly) -
SH 24 Lock Washer, 6mm (#7, Stand Assbly) - SC 02 Short Stand Top Support - 6.3 Contents of parts below.
User Manual - Page 10
...dust chute (B) as shown and install into the infeed opening. Cutterhead Guard
7. Install jointer infeed table lock knobs (K, T). Extension Table
Figure 10
8.0 Jointer setup
3.
Extension Table Adjustment
Disconnect machine...spring located on the cutterhead pivot shaft accordingly
Figure 9
Lock Knobs
The JJP-8BT Jointer-Planer comes equipped with two lock knobs to comply may cause serious...
User Manual - Page 15
... to be connected to a complete standstill. Use extreme caution when replacing any problems before further operation. Remove top portion of operation, see sect. 8.0, Jointer Setup, and sect 9.0, Planer Setup on both pulleys.
5.
To change the mode of belt (D) from pulley (E) while manually rotating pulley (F). Contact with cutterhead knives will cause serious injury.
3. Slide...
User Manual - Page 20
... or replace knives. Allow wood to dry or use different stock if necessary. Cutting too deeply.
Cutting too deeply.
Use slower rate of dust or debris. See sect. 11.1, Cutterhead Knife Adjustment.
Align knives per sect. 11.1, Cutterhead Knife Adjustment.
Jointer
Trouble
Probable Cause
Finished stock is higher than knife. 16.0 Troubleshooting the JJP-8BT...
User Manual - Page 21
...as described in sect. 11.1, Cutterhead Knife Adjustment.
Planer
Trouble
Probable Cause
Snipe
Inadequate support of dust or debris. Knives cutting against grain. Dull knives...knife slots are clean and free of long boards. Knives incorrectly set .
Sharpen or replace. 16.2 Performance Troubleshooting - Planing wood with extension rollers.
Sharpen knives. Adjust proper ...
User Manual - Page 22
...parts or reach our service department, call will not start/ restart or repeatedly trips circuit breaker or blows fuses. Having the Model Number and Serial Number of correct size. Remedy
1. Verify unit is probably a loose electrical lead. Set...17.0 Replacement Parts
Replacement parts are not electrical in the Start position (see sect. 10.1, Power).
16.3 Mechanical Troubleshooting - Planer...
User Manual - Page 25
Part No. Description
Size
Qty
123 JJP8BT-123 Socket Head Cap Screw M6x15 2 124 JJP8BT-124 Drive Chain...1 125 JJP8BT-125 Gear...1 126 JJP8BT-126 Pulley ...1 127 TS-1533062 Pan Head Machine Screw M5x20 3 128 JJP8BT-128 Key...1 129 JJP8BT-129 Belt...1 130 JJP8BT-130 Shaft ...2 131 JJP8BT-131 Front Support Cover 1 132 JJP8BT-132 JET Nameplate 1 133 JJP8BT-133 Key...1 ...
User Manual - Page 35
...
35 Part No. Description
Size
Qty
1 JJP8BT-901 Stand Top Support, Short 2 2 JJP10BT-902 Leg...4 3 JJP10BT-903 Support Plate, Long 2 4 JJP8BT-904 Support Plate, Short 2 5 JJP10BT-905 Stand Top Support, Long...our service department at 1-800-274-6848 and request Stand for JJP-8BT, stock number # 707402.
17.2.2 Jointer/Planer Stand - 17.2.1 Jointer/Planer Stand -
Parts List
Index ...
User Manual - Page 36
JJP-8BT
36
Overload Switch L
N
Power Switch Start
Switch
Outlet
Power Cord Plug
Stop
E
0.33uF/275V C
Stator
Stator
Rotor
M 1~
Rotor
(Yellow and green wire) E 18.0 Electrical Connections -
JET Tools JJP-8BT Reviews
We have not received any reviews for JET Tools yet.