JET Tools HVBS-712 Support and Manuals
Get Help and Manuals for this JET Tools item
This item is in your list!
View All Support Options Below
Free JET Tools HVBS-712 manuals!
Problems with JET Tools HVBS-712?
Ask a Question
Free JET Tools HVBS-712 manuals!
Problems with JET Tools HVBS-712?
Ask a Question
Popular JET Tools HVBS-712 Manual Pages
User Manual - Page 1
M-414559 Edition 2 11/2015
Copyright © 2015 JET Operating Instructions and Parts Manual
Horizontal-Vertical Band Saw
Models HVBS-712, HVBS-712D
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
HVBS-712D Deluxe model shown
Part No.
User Manual - Page 3
...instructions for the best and safest performance. Do not stand on -off the machine before starting by adjusting blade guides...tools in loss of the blade or cutter.
32.
Insert through hole in dangerous environment. Maintain tools with the following safety notices used in this manual...daily. Feed work area well lighted.
36. Replace dirty or weak coolant.
35. If in good condition. Keep ...
User Manual - Page 4
Parts List ...24 13.0 Electrical Connections - Exploded View 22 12.1.2 HVBS-712/712D Bow Assembly - Exploded View 23 12.1.3 HVBS-712/712D - 3.0 Table of contents
Section
Page
1.0 IMPORTANT SAFETY INSTRUCTIONS ...2 2.0 On-off switch padlock ...3 3.0 Table of contents...4 4.0 About this manual ...5 5.0 Specifications ...6 6.0 Setup and assembly...8
6.1 Shipping contents...8 6.2 Tools ...
User Manual - Page 5
... your local supplier or JET. Read and understand the entire contents of this document. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. Failure to provide consistent, long-term operation if used in accordance with the instructions as set forth in this manual before attempting assembly or...
User Manual - Page 6
...codes.
6 Square at 90 degrees 1(H) x 12(W) in 1(H) x 12(W) in 2(H) x 11-1/4(W) in 2(H) x 11-1/2(W) in 4(H) x 11(W) in 4(H) x 11(W) in 7(H) x 10-1/4(W) in 7(H) x 10-3/8(W) in. 5.0 Specifications
Model number HVBS-712D HVBS-712...ft. (200cm).........16AWG x 3C, length 6-1/2 ft. (200cm) Power plug installed 120V 120V Recommended circuit and fuse/breaker size 1 15A 15A
Capacities: Round at...
User Manual - Page 8
6.0 Setup and assembly
Read and understand all contents for shipping damage. E 2 Supports (1 long, 1 short) - H (712D only) 1 Work stop assembly - Bend ends of shipping carton with contents list in this manual show 712D Deluxe model.
C 4 Wheels - I (712 only)
1 Hardware package (p/n HVBS712-HP): 1 Lock screw - Procedures for assembly
Wrenches, 10mm and 19mm #2 ...
User Manual - Page 9
... by tightening set screw (H4) onto rod flat. Figure 6-6: installing work stop (712D only)
712 only: Install work stop (712 only)
6.
Figure 6-4: shipping bracket removal
4. Install work stop block onto rod and secure with flat head screws (HP5).
Secure position of work stop bracket (see Figure 7-1) must be used as infeed table in vertical mode (models 712 and...
User Manual - Page 10
... a properly grounded outlet can result in D. The temporary adapter should be installed by a qualified electrician. The tool has a grounding plug that looks like the plug illustrated in a risk of electric shock. and after
10 Local codes take precedence over recommendations.
7.1 GROUNDING INSTRUCTIONS
This machine must be reconnected for use on a circuit with circuit breaker...
User Manual - Page 19
...tools running on the band saw should be performed by an authorized service representative.
11.0 Troubleshooting HVBS-712/712D Band Saw
11.1 Mechanical and electrical problems...Install correct fuses or circuit breakers.
Replace blade immediately. Replace pump.
* WARNING: Some corrections may require a qualified electrician.
19 Replace dirty coolant; Low voltage.
Replace...instructions...
User Manual - Page 24
... Nut M10 1 25 TS-0060051 Hex Cap Screw 3/8" x 1 4 26 TS-0720091 Lock Washer 3/8 4 27 HVBS712-27 Cylinder Support Shaft 1 28 TS-0267041 Set Screw 1/4" x 3/8 1 29 HVBS712-29 Lower Cylinder Support 1 33 TS-0680081 Flat Washer 5/8 4 34 5518229N Wheel 8 4 35 HVBS712-35 Wheel Shaft 2 36 5518231N Cotter Pin * ...4 37 HVBS7MW-6 Toggle Switch with Guard Assembly (includes...
User Manual - Page 28
Stop Rod (712 only Base model 1 JET-113 JET Logo with
28 Warning Label (not shown 1 HVBS712-HP Hardware Package (includes items with 3M Adhesive (not shown 113 x 47mm 1 LM000136 ID Label HVBS-712 (not shown Base model 1 LM000137 ID Label HVBS-712D (not shown Deluxe model 1 LM000138 Motor Label (not shown 1 HBS1018W-205 ........ Index No Part No
Description
Size
Qty
...
User Manual - Page 30
... Support Please contact Technical Service by calling 1-800-274-6846, 8AM to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair, alterations or lack of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846. Please contact Technical Service at any reason whatsoever. Please note that you specific legal rights, subject to parts...
JET Tools HVBS-712 Reviews
Do you have an experience with the JET Tools HVBS-712 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for JET Tools yet.
Earn 750 points for your review!