JET Tools JAT-710 Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools JAT-710 manuals!
Problems with JET Tools JAT-710?
Ask a Question
Free JET Tools JAT-710 manuals!
Problems with JET Tools JAT-710?
Ask a Question
Popular JET Tools JAT-710 Manual Pages
User Manual - Page 2
... failures due directly or indirectly to the JET brand.
2 JAT-710 Orbital (Jitterbug) Sander
Please note that you specific legal rights, subject to applicable state law. More Information JET is Covered This warranty covers any defects in interest to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair, alterations or lack of its successors...
User Manual - Page 3
... holds itself harmless from heat and sharp edges. JET 3 Wear gloves and protective clothing if operation produces sparks or flying particles. Check air hoses for other masonry products.
• Arsenic and chromium from that are not safety glasses.)
6. Replace warning labels if they are specifically designed to these chemicals, work in potentially explosive...
User Manual - Page 4
...Do not use power tools in minor injury and/or possible tool damage.
4 JAT-710 Orbital (Jitterbug) Sander Use both hands to rain. Keep children away.
26. The right tool will do not hold...; Maintain tools with the following safety notices used in the air stream. Do not lubricate the tool with a jitterbug orbital sander.
38. Do not dispose of the air tool into fire. Specific warnings for...
User Manual - Page 5
...covering the safe operation and maintenance procedures for a JET Model JAT-710 Pneumatic Orbital (Jitterbug) Sander This manual contains instructions on the cover of operator and bystanders should accompany it. JET can also be first priority. JET 5 The instructions and warnings in accordance with any tool operation, safety of this manual for future reference. Record the serial number and...
User Manual - Page 6
... kPa) 16.6 m/s2 105 dB(A) Variable speed Palm 7-3/8 in .
Tool specifications
Model number Stock number Pad size Horsepower Average air consumption Air inlet Air hose inside diameter Required air pressure Vibration value Noise level 1 Power setting Grip Overall Length Housing material Net weight Shipping weight
JAT-710 505710 3-2/3 x 6-1/2 in. 0.3 4 CFM 1/4 in . (3.35 mm) Aluminum 4.06 lb...
User Manual - Page 7
... Disconnect air. Air system requirements
1. Figure 1 1. Repeat for the tool.
3. Set air pressure to tool specifications). Remove protective cap from tool.
2. If done manually, proceed as follows:
1. Wipe off housing with an inline oiler, or manually. Excessive hose length will cause pressure drop.
2. JET 7 NOTE: Air tool oil not provided; Do not use a damaged...
User Manual - Page 8
... which may enter the tool and cause damage.
5. Change filters on the air system on 70-to-100 psi (pounds per square inch) air pressure measured at maximum setting, the air wrench is too small or the air compressor CFM is required, use moisture traps at a specialized facility.
8 JAT-710 Orbital (Jitterbug) Sander
Use...
User Manual - Page 10
...clean air filter on components. Lubricate with gum solvent. Clean or replace. Troubleshooting JAT-710 Orbital (Jittebug) Sander
Any disassembly of air is connected without throttle lever being pressed. For problems not addressed below, contact JET technical service at 800-274-6846.
Problem
Possible cause
Remedy
Tool will not start. Loss of air transmission lines, hoses, fittings, or...
User Manual - Page 11
Please have the stock number and serial number of your tool available when you call 1-800-274-6848 Monday through Friday, 8:00 a.m.
JET 11 to 5:00 p.m. Replacement parts
To order parts or reach our service department, call , so that we may serve you quickly and accurately. CST.
User Manual - Page 13
#505710, JAT-710, Orbital (Jitterbug) Sander - Description
Qty
1
24 JAT710-24 End plate
1
1
25 JAT710-25 Rotor shaft
1
1
26 JAT710-26 Key
1
1
27 JAT710-27 Gasket
1
4 1
28
JAT710-28
Screw 5x10 (with #29 spring washer)
1
1
30 JAT710-30 Base
1
1
31 JAT710-31 Rubber post
4
1
32 JAT710-32 Cap screw M5x16
2
4
33 JAT710-33 Cap screw M5x38
2
2
34 JAT710-34 Balancer
1
1...
User Manual - Page 14
This page intentionally left blank. 14 JAT-710 Orbital (Jitterbug) Sander
User Manual - Page 15
This page intentionally left blank. JET 15
JET Tools JAT-710 Reviews
We have not received any reviews for JET Tools yet.