JET Tools JPS-10TS Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools JPS-10TS manuals!
Problems with JET Tools JPS-10TS?
Ask a Question
Free JET Tools JPS-10TS manuals!
Problems with JET Tools JPS-10TS?
Ask a Question
Popular JET Tools JPS-10TS Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
10-inch ProShop™ Table Saw with Riving Knife
Model JPS-10TS
(shown with steel wings and 30" rail set)
for serial no. 14053173 and higher
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No. M-708490 Revision C 05/2014 Copyright © 2014 JET
User Manual - Page 2
... they may deem necessary for further clarification.
JET® branded products are not sold in workmanship or materials subject to applicable state law. Machine Accessories; Manual Hoists; Please contact Technical Service at any reason whatsoever.
Please note that are not binding. The specifications listed in interest to parts, fittings, and accessory equipment which varies in...
User Manual - Page 3
... Stand Assembly - Parts List 35 16.4.1 Cast Iron Wings - 2.0 Table of contents
Section
Page
1.0 Warranty and Service ...2 2.0 Table of contents ...3 3.0 Safety warnings ...4
3.1 Kickback ...5 4.0 About this manual ...6 5.0 Glossary ...7 6.0 Features ...8 7.0 Specifications ...8 8.0 Setup and assembly ...10
8.1 Shipping contents...10 8.2 Unpacking and cleanup ...11 8.3 Installing legs ...11...
User Manual - Page 4
... the switch is damaged should be properly repaired or replaced.
19. A guard or other reproductive harm. This table saw , do not have a clear understanding of the machine, a guard or other purposes, JET disclaims any real or implied warranty and holds itself harmless from lead based paint.
4 Check damaged parts. Provide for adequate space surrounding work with...
User Manual - Page 5
...into the blade.
• Use a push stick to avoid the most vulnerable part of the blade when cutting. Keep saw blade.
33. Pay particular attention to perform any operation freehand.
36. Never ... the right tool at all times so that you if kickback does occur:
• Stand to support the workpiece.
• Make sure that can be fed parallel to blade. Follow instructions for the ...
User Manual - Page 6
.... Retain this document. Familiarize yourself with the instructions as set forth in this manual for a JET Model JPS-10TS ProShop™ Table Saw. If the machine transfers ownership, the manual should accompany it.
This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. If there are used, always...
User Manual - Page 8
... capacitor start, with 52" Rails/Fence Kit & Wood Ext. 6.0 Features
7.0 Specifications
Figure 1
Model number ...JPS-10TS
Stock numbers:
(Steel Wings)
(Cast Iron Wings)
Saw Unit only with Steel Wings 708490
Saw Unit only with Cast Iron Wings ...708491
Saw with 30" Rails/Fence Kit 708492K 708494K
Saw with reset button Horsepower...1-3/4 HP Phase...single Voltage...115/230V (prewired...
User Manual - Page 10
...- Use Figures 3 and 4 to the table saw.
1 Table saw (not shown) 1 Blade (not shown) 1 Extension wing - 8.0 Setup and assembly
8.1 Shipping contents
Carton contents (see Figure 2)
NOTE: Some parts may have come preassembled to help identify hardware...screw (HP-11) 1 5mm Lock washer (HP-12)
Figure 2
Figure 3 Tools included for assembly 1 23mm Combination wrench 1 10-12mm Open end wrench 1 11-13mm...
User Manual - Page 11
... to Figure 5:
1. Remove all assembly instructions before attempting assembly. Keep saw - Do not discard carton or packing material until wings are installed.)
3. Hand tighten only.
2. On front of table saw, slide bushing (HP-2) onto shaft (A) followed by -four or similar piece of wood under the rear of each foot.
this manual. Report damage, if any , to...
User Manual - Page 16
... illustrated in A, Figure 20. It is recommended that the table saw comes with a plug designed for use on 115 volt power, be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. Local codes take precedence over recommendations.
9.1 Grounding instructions
1. The plug must be connected to a dedicated 20 amp...
User Manual - Page 17
...Table Saw is equipped with a push-button switch that is inaccessible to children and others not qualified to restart. junction box (A, Figure 21), tilt blade to maximum height.
17
The blade should be replaced...set button on front of power and overheating. Make sure your machine from unauthorized operation and accidental starting by young children, the use the tool...in this manual.
9.4 ...
User Manual - Page 20
...show your saw model, but procedures are conditions which occur when a workpiece binds on the right side of saw blade so that is made with the fence on the saw blade or binds between saw blade. ...use the fence as miter gauge and rip fence. Support the work . Figure 30 Dull, badly set, improper, or improperly filed cutting tools and cutting tools with gum or resin adhering to lift up and ...
User Manual - Page 25
... table surface and T-slots with 6 or 7 drops of light machine oil.
ˆ Worm gears and threads should be aware of the condition of the following maintenance schedule assumes the saw blade. Routinely check the condition of your machine. Cleaning Clean the JPS-10TS according to ensure maximum performance. Note-The following items and repair or replace...
User Manual - Page 26
Mobile Base Extension Kit
26 Universal Mobile Base, adjustable up to order, or call JET at the phone number on the cover. # 708489 - 14.0 Optional accessories
These accessory items, purchased separately, can enhance the functionality of your dealer to 36" x 36" # 708158 - Contact your table saw. Dado Insert for ProShop Saw with Riving Knife # 708119 -
User Manual - Page 27
...Table top not parallel to blade. Pointer bracket is hitting the cover. Inspect cord or plug for business hours, www.jettools.com). Replace saw blade. Adjust fence parallel to blade. To order parts or reach our service....
27 15.0 Troubleshooting the JPS-10TS
Symptom
Possible Cause
Motor... degree stop is defective.
Install correct fuses or circuit breakers...
JET Tools JPS-10TS Reviews
We have not received any reviews for JET Tools yet.