Product Guide
Page 47
...same cable, the maximum transfer rate between the drives can be sure to connect the drive to the desktop board. Installing and Replacing Desktop Board Components Connecting the IDE Cable The Intel® boxed desktop board package includes two IDE cables. For example, do not connect an ATA hard drive as shown in ... P2 and P3, to an ATAPI CD-ROM drive. The 40-contact 80-conductor cable supports ATA-66 and ATA-100 transfer protocols and is blue and labeled P1, to the desktop board as a slave to the drives. Connecting the IDE Cable (the D815EEA2 Board Is Shown) 47 B A OM11159 ...
...same cable, the maximum transfer rate between the drives can be sure to connect the drive to the desktop board. Installing and Replacing Desktop Board Components Connecting the IDE Cable The Intel® boxed desktop board package includes two IDE cables. For example, do not connect an ATA hard drive as shown in ... P2 and P3, to an ATAPI CD-ROM drive. The 40-contact 80-conductor cable supports ATA-66 and ATA-100 transfer protocols and is blue and labeled P1, to the desktop board as a slave to the drives. Connecting the IDE Cable (the D815EEA2 Board Is Shown) 47 B A OM11159 ...
Product Guide
Page 67
...capabilities to be changed. Check the hard disk drive's specifications for IDE devices. Feature Drive Installed Type Primary/Secondary IDE Master/Slave Submenus Options None • None • User • Auto (default) • CD-ROM • ATAPI Removable • Other ATAPI • IDE Removable None • ...the IDE submenus. Table 18. Auto fills-in capabilities from the hard disk drive to memory. For brevity, only one example is installed. Enables or disables LBA mode control. PIO Mode (Note) Note: These configuration options appear only if an IDE device is shown...
...capabilities to be changed. Check the hard disk drive's specifications for IDE devices. Feature Drive Installed Type Primary/Secondary IDE Master/Slave Submenus Options None • None • User • Auto (default) • CD-ROM • ATAPI Removable • Other ATAPI • IDE Removable None • ...the IDE submenus. Table 18. Auto fills-in capabilities from the hard disk drive to memory. For brevity, only one example is installed. Enables or disables LBA mode control. PIO Mode (Note) Note: These configuration options appear only if an IDE device is shown...
Product Guide
Page 75
...will reflect as many boot entry vector (BEV) boot devices (for example, Intel UNDI, PXE devices) and SCSI CD-ROM drives as are installed, up to each boot device in order by type, the BEV devices and SCSI CD-ROM drives are all listed at this level. 2. 75 The operating system assigns... For example, assume that the default boot order is for the first through final boot devices are installed on the system: two removable devices, two hard drives, two ATAPI CD-ROMs, and an Intel UNDI (Universal Network Device Interface), PXE device. Both removable devices would appear as the first and ...
...will reflect as many boot entry vector (BEV) boot devices (for example, Intel UNDI, PXE devices) and SCSI CD-ROM drives as are installed, up to each boot device in order by type, the BEV devices and SCSI CD-ROM drives are all listed at this level. 2. 75 The operating system assigns... For example, assume that the default boot order is for the first through final boot devices are installed on the system: two removable devices, two hard drives, two ATAPI CD-ROMs, and an Intel UNDI (Universal Network Device Interface), PXE device. Both removable devices would appear as the first and ...
Product Guide
Page 77
... factory defaults. Table 30. Loads the custom defaults for all the Setup options. If this menu, select Exit from the available ATAPI CD-ROM drives. Feature 1 ATAPI CDROM Drive (Note) st ATAPI CDROM Drives Submenu Options Dependent on are set the selection as custom defaults...the Setup Program ATAPI CDROM Drives To access this menu, select Boot from flash memory. Exit Menu To access this memory is installed. Feature Exit Saving Changes Exit Discarding Changes Load Setup Defaults Load Custom Defaults Save Custom Defaults Exit Menu Description Exits and saves...
... factory defaults. Table 30. Loads the custom defaults for all the Setup options. If this menu, select Exit from the available ATAPI CD-ROM drives. Feature 1 ATAPI CDROM Drive (Note) st ATAPI CDROM Drives Submenu Options Dependent on are set the selection as custom defaults...the Setup Program ATAPI CDROM Drives To access this menu, select Boot from flash memory. Exit Menu To access this memory is installed. Feature Exit Saving Changes Exit Discarding Changes Load Setup Defaults Load Custom Defaults Save Custom Defaults Exit Menu Description Exits and saves...