Instruction Manual
Page 4
iii SUPPLIED ACCESSORIES q w r e t y u i o !0 q DC power cable (3 m 1 w Controller cable (10 cm†; 3.9 in 1 e Separation cable (3.4 m†; 11.2 ft 1 r Microphone (HM-133 1 t Fuse (20 A 1 y Microphone hanger 1 u Mounting screws, nuts and washers 1 set i Mobile mounting bracket 1 o Microphone connector plate with screw 1 set !0 Remote controller bracket 1 *HM-154 HAND MICROPHONE may be supplied with some versions. †Approx.
iii SUPPLIED ACCESSORIES q w r e t y u i o !0 q DC power cable (3 m 1 w Controller cable (10 cm†; 3.9 in 1 e Separation cable (3.4 m†; 11.2 ft 1 r Microphone (HM-133 1 t Fuse (20 A 1 y Microphone hanger 1 u Mounting screws, nuts and washers 1 set i Mobile mounting bracket 1 o Microphone connector plate with screw 1 set !0 Remote controller bracket 1 *HM-154 HAND MICROPHONE may be supplied with some versions. †Approx.
Instruction Manual
Page 9
.... • Optional OPC-440 MICROPHONE CABLE (5.0 m; 16.4 ft) is available to extend the microphone cable. • Optional OPC-441 SPEAKER CABLE (5.0 m; 16.4 ft) is available to extend the speaker cable. QUICK REFERENCE GUIDE Quick reference guide • Remote installation Controller Main unit • The supplied remote controller bracket and separation cable can support the weight of...
.... • Optional OPC-440 MICROPHONE CABLE (5.0 m; 16.4 ft) is available to extend the microphone cable. • Optional OPC-441 SPEAKER CABLE (5.0 m; 16.4 ft) is available to extend the speaker cable. QUICK REFERENCE GUIDE Quick reference guide • Remote installation Controller Main unit • The supplied remote controller bracket and separation cable can support the weight of...
Instruction Manual
Page 10
...IC-2820H. Controller Main unit 4-pin connector 6-pin connector IMPORTANT!- one end has 6 pins and the other end 4 pins. eAdjust the angle for remote installation, are supplied with the supplied connection cable as follows. Connect the controller and the main unit using self-tapping screws Flat washer Mounting bracket Mounting nut D Controller/Separation cable... connection Two connection cables, controller cable (10 cm; 3.9 in) for single body installation and separation cable (3.4 m; 11.2 ft) for your suitable ...
...IC-2820H. Controller Main unit 4-pin connector 6-pin connector IMPORTANT!- one end has 6 pins and the other end 4 pins. eAdjust the angle for remote installation, are supplied with the supplied connection cable as follows. Connect the controller and the main unit using self-tapping screws Flat washer Mounting bracket Mounting nut D Controller/Separation cable... connection Two connection cables, controller cable (10 cm; 3.9 in) for single body installation and separation cable (3.4 m; 11.2 ft) for your suitable ...
Instruction Manual
Page 11
.... GPS antenna Main unit Attach the supplied microphone connector plate after the microphone connection, otherwise the controller will separate from the main unit when the microphone cable is allowed. to [GPS ANT] GPS antenna cable length: approx. 5 m (16.4 ft) Mount the GPS antenna onto a convenient flat surface. NOTE When the GPS antenna...
.... GPS antenna Main unit Attach the supplied microphone connector plate after the microphone connection, otherwise the controller will separate from the main unit when the microphone cable is allowed. to [GPS ANT] GPS antenna cable length: approx. 5 m (16.4 ft) Mount the GPS antenna onto a convenient flat surface. NOTE When the GPS antenna...
Instruction Manual
Page 30
...i o !0 !1 q CONTROLLER CONNECTOR [CONTROLLER] (p. III) Connects the controller unit with a PL-259 connector and a 50 Ω coaxial cable for transmission and reception. t MICROPHONE CONNECTOR [MIC] (p. u COOLING FAN Rotates while transmitting. Also rotates while receiving depending on the setting in ...UT-123, is installed. 9 e GPS ANTENNA CONNECTOR [GPS ANT] (p. IX) Connects a 50 Ω antenna with the supplied controller or separation cable. r PACKET JACK [PACKET] (pgs. 120, 121) Connects a TNC (Terminal Node Controller), etc. The receiver can support 1200/9600 bps...
...i o !0 !1 q CONTROLLER CONNECTOR [CONTROLLER] (p. III) Connects the controller unit with a PL-259 connector and a 50 Ω coaxial cable for transmission and reception. t MICROPHONE CONNECTOR [MIC] (p. u COOLING FAN Rotates while transmitting. Also rotates while receiving depending on the setting in ...UT-123, is installed. 9 e GPS ANTENNA CONNECTOR [GPS ANT] (p. IX) Connects a 50 Ω antenna with the supplied controller or separation cable. r PACKET JACK [PACKET] (pgs. 120, 121) Connects a TNC (Terminal Node Controller), etc. The receiver can support 1200/9600 bps...
Instruction Manual
Page 157
... dB for the Taiwan version. : ±5.0 kHz (wide) ±2.5 kHz (narrow) : Less than 2.4 W at 25 W) only for the Taiwan version Receive standby 1.2 A (simultaneous receive) max. separation cable) D TRANSMITTER • Modulation system • Output power • Max. All stated specifications are inhibited for USA version and not guaranteed. • Type of...
... dB for the Taiwan version. : ±5.0 kHz (wide) ±2.5 kHz (narrow) : Less than 2.4 W at 25 W) only for the Taiwan version Receive standby 1.2 A (simultaneous receive) max. separation cable) D TRANSMITTER • Modulation system • Output power • Max. All stated specifications are inhibited for USA version and not guaranteed. • Type of...
Instruction Manual
Page 158
... low-speed data communication in DV mode and data cloning operation with key backlight. HM-154 HAND MICROPHONE OPC-347/1132 DC POWER CABLES OPC-347: 7.0 m OPC-1132: 3.0 m Same as memory channels or set mode contents for data cloning between transceiver and PC with...18 SPECIFICATIONS AND OPTIONS • Sensitivity (for data cloning between transceivers. Same as that supplied with the transceiver. OPC-1663 SEPARATION CABLE For separate installation. OPC-478/478U CLONING CABLE Used for RX bands- FM/AM; for your reference only): Frequency range 118-159.995 MHz Left band (µV) ...
... low-speed data communication in DV mode and data cloning operation with key backlight. HM-154 HAND MICROPHONE OPC-347/1132 DC POWER CABLES OPC-347: 7.0 m OPC-1132: 3.0 m Same as memory channels or set mode contents for data cloning between transceiver and PC with...18 SPECIFICATIONS AND OPTIONS • Sensitivity (for data cloning between transceivers. Same as that supplied with the transceiver. OPC-1663 SEPARATION CABLE For separate installation. OPC-478/478U CLONING CABLE Used for RX bands- FM/AM; for your reference only): Frequency range 118-159.995 MHz Left band (µV) ...