Hunter 82022 Support and Manuals
Get Help and Manuals for this Hunter item
View All Support Options Below
Free Hunter 82022 manuals!
Problems with Hunter 82022?
Ask a Question
Free Hunter 82022 manuals!
Problems with Hunter 82022?
Ask a Question
Popular Hunter 82022 Manual Pages
Owner's Manual - Page 1
Installation
Guide
ENGLISH
See page 2
Español
Vea la página 21
francais
Voir la page 41
82022 La Strada Bath Ventilator with Light
READ and SAVE THESE INSTRUCTIONS
42949-01 04/18/2007
Owner's Manual - Page 2
... PARTS SHOULD NEVER BE IMMERSED IN WATER. If you cannot lock the circuit breakers in a wall. This unit must be vented to a GFCI protected branch circuit.
7.
MAINTENANCE
The motor is designed for further information and requirements. You should replace the impeller at the phone number or address listed in the warranty.
2. Before installing, servicing...
Owner's Manual - Page 15
Existing Construction - accessible only from below
D11 EXISTING FAN
D12
F
Remove an existing fan and check to make sure the opening is large enough to duct connector.
ing (8"x 8 1/2"). D15
Attach existing ducting to accommodate the new motor hous-
F
Install the housing flush with the sheetrock and secure by tightening the pre-loaded screws into...
Owner's Manual - Page 16
D17
D18
G
H
Install the wiring cover plate.
DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. D20
I
... cover plate.
D19
I
Reinstall the motor by tightening the 2 screws. 42949-01 04/18/2007
D16
Fan Motor Light
Black 2 Pin
White
White
3 Pin Black Light *Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Black Switch ...
Owner's Manual - Page 19
... to feel the air movement. • Turn power on, replace fuse, or reset breaker. • Check all plug connections to be sure they are extremely quiet. Problem: Fan is secure. • Check the flapper to make sure it moves freely. Solution: • Harbor Breeze Fan Bath Ventilators are secure. • Check the wiring to make...
Owner's Manual - Page 20
... any part of your Hunter bath exhaust fan (except for glass fixtures and light bulbs) fails at any time within five years after the date of sale to you due to a defect in material or workmanship, we will repair or, at our option, replace the defective part free of charge for parts and labor performed at our nearest service...
Owner's Manual - Page 2
... fans must be grounded. METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN WATER. You should replace ...fan as a tag, to the receptacle). TO CLEAN GRILLE: Use a mild detergent, such as possible.
6. Acceptable for further information and requirements. Ductwork must point upward.
4. Please read specification label on the motor plate (located next to the service panel.
3. Installation...
Owner's Manual - Page 6
A15
A016
F
H
Install the wiring cover plate. Make sure all wiring connections are inside the box or under
the wiring cover plate. 6
Connect 4" duct and vent to be purchased.
42929-01 10/26/2010 Tape joints. A13
Route wires through the strain relief. A14
Fan Motor Light
2 Pin
Black White
White
3 Pin Black...
Owner's Manual - Page 9
..., an adapter may need
to the outside. B17
B18
Tighten screws.
B20
B21
G
H
Install the wiring cover plate. Make sure all wiring connections are inside the box or under the .../26/2010
Connect 4" duct and vent to be purchased.
9
B19
Fan Motor Light
2 Pin
Black White
White
3 Pin Black Light *Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch ...
Owner's Manual - Page 11
... an opening is large enough to make sure the opening for the housing. Use the motor housing as a template. 11
accessible from above
C11 EXISTING FAN
NO EXISTING FAN
OR
Remove an existing fan and check to accommodate the new
motor housing (8"x 8 1/2"). C13
Slide the mounting rails into brackets.
Existing Construction -
Owner's Manual - Page 13
DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. 13 C23
C24
G
H
Install the wiring cover plate. C22
Fan Motor Light
2 Pin
Black White
White
3 Pin Black Light *Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Black Switch 2 (AC In)
Connect wires as shown...
Owner's Manual - Page 15
ing (8"x 8 1/2").
accessible only from below
D11 EXISTING FAN
D12
F
Remove an existing fan and check to make sure the opening is large enough to duct connector.
D15
Attach existing ducting to accommodate the new motor hous- Existing Construction - F
Install the housing flush with the sheetrock and secure by tightening the pre-loaded screws into...
Owner's Manual - Page 16
D17
D18
G
H
Install the wiring cover plate.
D20
I
Connect wiring harness.
DO NOT ALLOW THE MOTOR TO HANG FROM ...and the housing. 16
J
Secure the motor by inserting the tabs and pushing up into position. D16
Fan Motor Light
Black 2 Pin
White
White
3 Pin Black Light *Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In)
White
Black Switch...
Owner's Manual - Page 20
... to be sure they are extremely quiet.
Trouble Shooting
Problem: Fan does not come on , replace fuse, or reset breaker. • Check...Problem: Fan is running, place your hand near the vents to make sure it matches the wiring diagram. If you need parts or service assistance, please call 888-830-1326 or visit us at our web site at http://www. Solution: • Harbor Breeze Fan Bath...
Owner's Manual - Page 21
... no replacement part can be provided, we will not be properly packed to avoid damage in transit since we will return your Hunter bath exhaust fan is required when requesting warranty service. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES.
Your Hunter bath exhaust fan should be responsible for repairs on all parts and labor costs for any Hunter bath exhaust fan...
Hunter 82022 Reviews
We have not received any reviews for Hunter yet.