Hunter 28425 Support and Manuals
Get Help and Manuals for this Hunter item
View All Support Options Below
Free Hunter 28425 manuals!
Problems with Hunter 28425?
Ask a Question
Free Hunter 28425 manuals!
Problems with Hunter 28425?
Ask a Question
Most Recent Hunter 28425 Questions
Problems With Remote Control
Hi, I tried to put a new battery for my remote control. I noticed Remote control Blue light on ( Hun...
Hi, I tried to put a new battery for my remote control. I noticed Remote control Blue light on ( Hun...
(Posted by Sandeman05 1 year ago)
Popular Hunter 28425 Manual Pages
Operation Manual - Page 2
...-830-1326. For ceilings higher than one of the fan blades was damaged in accordance with national and local electrical codes and ANSI/NFPA 70. Before installing your fan, record the following tools for replacement. Save these instructions.
• Use only Hunter replacement parts. • To reduce the risk of personal injury, attach the fan
directly to the support structure of the...
Operation Manual - Page 3
If you cannot check off every item, see the preparing a new fan site section for instructions on properly preparing the site for your fan and to prepare the site prior to installing the fan.
Support Brace
Ceiling Joist
Approved
Connector
9' Minimum Ceiling Height
7' Minimum to joist or support brace by wood screws and washers through inner holes of outlet box...
Operation Manual - Page 4
... You have now successfully prepared your ceiling fan, continue with four neoprene noise isolators. Your fan comes with the installing the ceiling plate section. Attach a 2" x 4" support brace between the ceiling plate and ceiling by inserting the raised areas on how to Figure 8.
© 2005 Hunter Fan Company The sup-
Check the support brace to Figure 7. 4. Approved Connector...
Operation Manual - Page 5
... remove this coating; Screw the downrod into the 9/64" pilot holes; Installing the ceiling plate
Allen Head Set Screw
Figure 12 - the coating prevents the downrod from the fan through the canopy, the canopy trim ring, the adapter cover as shown in the wood support structure.
Insert the downrod through the downrod. 3. Inserting the isolators...
Operation Manual - Page 6
...-01 02/24/2005
© 2005 Hunter Fan Company WARNING: Fan may fall if not assembled as shown in these installation instructions. Tighten the three screws.
#6-32 x 3/8" screw
installing the light bulbs
Install 4 B10, 40 Watt Max bulbs. 6
installing the adapter cover
1. Use the note and arrow engraved in the ceiling plate to assist in the top housing. hanging...
Operation Manual - Page 7
... towards the canopy as shown in the canopy and the ceil- ing plate are assembled, securely tighten all three screws ...codes and ANSI/NFPA 70. Power Black Wires
in the same direction and should use a qualified electrician.
Installing the canopy
installing the canopy trim ring
1. To easily install the canopy trim ring, locate the two tabs on the canopy.
Wiring the fan
installing...
Operation Manual - Page 8
... the screw.
© 2005 Hunter Fan Company Grommet
Fan Blade
Blade Iron
Medallion
Figure 22...installed screws. Figure 20 - Some fans feature a decorative medallion as well as shown in Figure 23, and attach lightly to the blade iron
41860-01 02/24/2005
Plug Connector
Figure 24 - 8
Tab Indicator Canopy Trim Ring
Canopy
Figure 19 - Removing the canopy trim ring
assembling the blades
Hunter fans...
Operation Manual - Page 9
... as shown in a particular installation. These limits are designed to radio communications. This equipment generates, uses and can be determined by Hunter Fan Company may cause harmful interference ...the fan to Part 15 of the way when assembling the light fixture.
7. Line up the key slots in accordance with electrically reversible ceiling fans rated at 1.0 amp or less, and fan incandescent...
Operation Manual - Page 10
... polarity on the battery as shown in installing the battery.
41860-01 02/24/2005
Battery Compartment
Dip Switches
Cover
Figure 31 - Replace the cover. Continue to installing the battery. See Figure 29. 2....and don't over tighten. Use the inner mounting holes. Installing the battery and setting the dip switches
© 2005 Hunter Fan Company Do not remove the cover plate.
2. Line ...
Operation Manual - Page 11
... the event of the dip switch code in warm weather to cool the room with a direct breeze. NOTE: You may inadvertently change the dip switch code settings for it as you are different from the previously installed fan. To start the fan press the selected speed button to run the fan at the ceiling around the room without causing...
Operation Manual - Page 12
..., Tennessee 38114
41860-01 02/24/2005
© 2005 Hunter Fan Company Surface smudges or an accumulation of the LIGHT buttons maintains the desired brightness level set previously. An artistic agent may be removed by press the UP LIGHT or DOWN LIGHT button. troubleshooting
Problem: Nothing happens; Check the plug connection in the same manner...
Hunter 28425 Reviews
We have not received any reviews for Hunter yet.