Hunter 21101 Support and Manuals
Get Help and Manuals for this Hunter item
View All Support Options Below
Free Hunter 21101 manuals!
Problems with Hunter 21101?
Ask a Question
Free Hunter 21101 manuals!
Problems with Hunter 21101?
Ask a Question
Popular Hunter 21101 Manual Pages
Installation Guide - Page 1
... 2 - 3
Step 3 Install a Support Brace, If Necessary
Determine if there is a ceiling joist directly above the floor and the ceiling is suitable, go to your new Hunter fan. Position it to allow you cannot check off position, securely fasten a prominent warning device, such as described on this page. If you are turned off. For instructions to install your ceiling fan, go...
Owner's Manual - Page 1
Date Purchased
Where Purchased
Type 2 Models
Owner's Guide and Installation Manual
English
Español
Form# 42678-01 20090608 ©2009 Hunter Fan Co. Model Name
Model No.
For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual.
Owner's Manual - Page 2
...; Troubleshooting 13
Welcome
Your new Hunter® ceiling fan is an addition to your fan. Before installing your fan, for many years.
Never insert foreign objects between rotating fan blades. • To reduce the risk of the fan motor housing). This installation and operation manual gives you cannot lock the circuit breakers in the off the circuit breakers to the service panel...
Owner's Manual - Page 3
... provides you can install your Hunter fan in one of three ways, depending on ceiling height and your Hunter fan, use the accessories, follow the instructions included with each product.
To install and use only Hunter speed controls. Angled Mounting Style
8 12
Angled Mounting recommended for a vaulted or angled ceiling
Support Brace
Low Profile Mounting Style
Ceiling Outlet Box
Low...
Owner's Manual - Page 4
... tools for any parts are installing more than one fan, keep the fan blades and blade irons (if applicable) in sets, as they were shipped.
4 42678-01 • 06/08/09 • Hunter Fan Company Refer to a licensed installer or electrician. Installing Multiple Fans? 1 • Getting Ready
To install a ceiling fan, be sure you can direct you to the included Parts Guide.
If any shipping...
Owner's Manual - Page 5
.../09 • Hunter Fan Company Your fan comes with the pilot holes you
drilled in the ceiling plate into the 9/64" pilot holes; Align the slotted holes in diameter. The pilot holes should be 9/64" in the ceiling plate with four preinstalled noise isolators.
Place a flat washer on the screws. 2 • Installing the Ceiling Plate
CAUTION: To...
Owner's Manual - Page 6
...; 06/08/09 • Hunter Fan Company Once assembled, do not remove the downrod.
Hanging the Fan: Note: To hang the fan, you must tilt the canopy to hang the fan. Raise the fan and align the slots in these installation instructions.
3-1. Unbundle the wires from unscrewing. CAUTION: The adapter has a special coating on
the ceiling plate. 3-8. For Low...
Owner's Manual - Page 7
...01 • 06/08/09 • Hunter Fan Company
fsdfsdf
Wire Connector Dual Switch Wiring
...them carefully back through the ceiling plate into the outlet box.
4-7. Before attempting installation, make sure the power...ceiling to the green ground wire (grounded) from the ceiling plate and the green ground wire from the fan. 4-5. Spread the wires apart, with national and local electrical codes...
Owner's Manual - Page 8
... holes on the ceiling plate. Using both hands, push the canopy trim ring up to align the canopy screw holes with the screw holes aligned, partially install two canopy screws into place.
Step 5-1 Tab Groove
Step 5-2
Step 5-3 Canopy Canopy Trim Ring
Canopy Screw
8 42678-01 • 06/08/09 • Hunter Fan Company Align...
Owner's Manual - Page 9
... blade mounting screw, then securely tighten both mounting screws. If your fan has grommets, insert them by hand into the holes on the blades.
...Hunter Fan Company If you used grommets, the blades may include blade grommets. Your fan may appear slightly loose after screws are installed in the motor to the fan. 6 • Assembling the Blades
Hunter fans use several styles of fan...
Owner's Manual - Page 10
...; 06/08/09 • Hunter Fan Company CAUTION: Make sure the upper switch housing is securely attached to the upper switch housing with this fan model.
7-1.
Turn the housing counterclockwise until... slots. Align the keyhole slots in the narrow end of the housing.
7-3. 7 • Installing the Light Kit
WARNING: Use only the light fixture supplied with three #6-32 x 3/8" housing ...
Owner's Manual - Page 11
Remove the protective wrap from each of the shades. 7-8. 7 • Installing the Light Kit (continued)
Shade Light Bulb
7-7. Install the three 60-Watt candelabra light bulbs (included). Remove the plastic from the silhouette on the motor housing before starting the fan. Install the shades. 7-9. Steps 7-8 - 7-9
11 42678-01 • 06/08/09 • Hunter Fan Company
Owner's Manual - Page 12
... chain slowly to change settings. • Release slowly to the fan.
8-2. You may use a soft brush or lint-free cloth to cool the room with a furniture polishing cloth. Clean painted and high-gloss blades in warm weather to prevent scratching. 8 • Operating and Cleaning Your Ceiling Fan
8-1. In winter, having the fan draw air upward...
Owner's Manual - Page 13
... wobbles when operating, use the enclosed balancing kit and instructions to the wiring the
fan section. 3.
9 • Troubleshooting
Problem: Nothing happens; Check the plug connection in the switch housing. 4. Remove the shipping bumpers. fan does not move.
1. Turn power on
1. Problem: Noisy operation. 1. Hunter Fan Company 7130 Goodlett Farms Pkwy. #400 Memphis, Tennessee 38016...
Parts Guide - Page 1
...Hunter Fan Company • 7130 Goodlett Farms Pkwy. #400 • Memphis, TN 38016 • www.hunterfan.com • 98000-01-995 06-01-2010 • ©2010 REFER TO THE INSTALLATION MANUAL FOR FULL ASSEMBLY INSTRUCTIONS.
Parts List
Item # Item Name
1 * Hanging System Kit
2
Ceiling...Pendant
202 Light bulb / Bulb
150 Globe/Shade
Model #
21101
Asm. Hardware (Drawn to Scale)
x 1...
Hunter 21101 Reviews
We have not received any reviews for Hunter yet.