Honeywell VISTAKEY Support and Manuals
Get Help and Manuals for this Honeywell item
View All Support Options Below
Free Honeywell VISTAKEY manuals!
Problems with Honeywell VISTAKEY?
Ask a Question
Free Honeywell VISTAKEY manuals!
Problems with Honeywell VISTAKEY?
Ask a Question
Popular Honeywell VISTAKEY Manual Pages
User Guide - Page 3
... OF CONTENTS
OVERVIEW ...4
INTRODUCTION...4
USER COMMANDS ...5 Access Control...6 #73 ...6 #74 ...7 #75 ...8 #79 ...10 Output Device Control (#77) ...10 Schedule Control (#80)...12
PERFORMING ACCESS CONTROL CARD FUNCTIONS 16 Adding Cards ...18 Editing Cards ...27 Auto Delete ...34 Block Delete...36 Manual Delete...37 Quit Card Function Programming 38
PERFORMING SCHEDULING OPERATIONS 39 Time...
User Guide - Page 4
... system, additional commands and operational capabilities are added to your existing security system User Guide.
- 4 - The VistaKey-SK, interfaced to your ownership of a UL-approved ADEMCO VistaKey-SK Access Control Unit. The VistaKey-SK: • Helps to reduce unwanted alarms caused by improper keypad operation by simplifying operation through the use of a card-swipe reader or wireless...
User Guide - Page 6
... be assigned to add, remove, or edit cards in which the keypad being used. • The request will automatically relatch after a time interval set by your system installer. The access control commands may be used to directly control access points or to a card with an access
group assignment which includes the point and partition in the system's cardholder...
User Guide - Page 7
... the partition is armed when an armed restriction has been programmed. User Commands (cont'd)
#74
The #74 command may be used to accept the entry.
Enter the #74 command as follows:
User Code + # + 74
The following message is displayed on the keypad:
Access Point 00-31
Enter two digits (from 01 through any action...
User Guide - Page 10
..., bypass zones, etc. For instructions on using this command, refer to which the keypad belongs.
• The VISTA user number must have a level assignment of Master. • If the partition is armed, Armed Restriction is in the system's cardholder database. under user control. Output Device Control (#77) The #77 Output Device Control may used to add...
User Guide - Page 16
... performing access control card functions, only VISTA User Numbers that will be set for the access goup. (Armed Restriction for assignment to a card or cards, must be accepted. To assign VISTA User Numbers, refer to the procedures in your system installer.
- 16 - Keep the following advisories in the alarm system panel by your alarm system manual.
• VISTA User...
User Guide - Page 17
... was not set . A card was given access to a point by your system installer and Armed Restriction was set . To begin #79 Card Function Programming, enter User Code + # + 79. See the two examples below:
1. The following table illustrates the card's capabilities.
The following table illustrates the card's capabilities. Card
Executive VISTA User Access Through Access Disarm
Privilege...
User Guide - Page 18
... for procedural instruction. AUTO Delete? prompt. When the choice desired is displayed, stop pressing 0 and refer to the "Adding Cards" paragraph below. If you press 1, the following prompt is displayed.
Adding Cards
Add Card? 1=Yes 0=No
Press 1 to another choice.
Press [*] to change card data. Performing Access Control Card Functions (cont'd)
Access Point
Enter...
User Guide - Page 19
Performing Access Control Card Functions (cont'd)
SWIPE CARD xxx-xx-xxxxxxx
Swipe card or manually enter the (12-digit) card code to accept the entry. Note that your entries will edit the existing card data.
If block entry was selected on the first card, the system ...
User Guide - Page 20
... cardholder with executive privilege from the access group; Performing Access Control Card Functions (cont'd)
This occurs regardless of whether the cardholder's access group is enabled via scheduling or whether his access group is enabled to an access group that has executive privilege enabled, this feature can be accepted when the VistaKey is operating in RCM.
- 20 - NOTE...
User Guide - Page 22
... = Normal (no effect on the usage count. NOTE: If you set the same card to occur.
Enter 00 for this cardholder.
UNLIMITED USE
00
↓ VISTA Card ID Number
001 Expire Month
NO EXPIRATION
00
NOTE: Numbers toggle. Performing Access Control Card Functions (cont'd)
↓ VISTA Card ID Number
001 Expire use . For example, pressing...
User Guide - Page 23
Performing Access Control Card Functions (cont'd)
NOTES:
• Cards expire at midnight of month selections.
• If you set a card to expire by time and also set the same card to an access group that partition. Press [*] to accept the entry.
↓ VISTA Card ID Number 001 Vista User#
000
Enter a three-digit VISTA User number.
Press [*] to accept...
User Guide - Page 24
...Programming section of 000 will be identified as the cardholder is selected.
• The partition rights and privileges of the VISTA User assigned should be consistent with VISTA User number of this manual for that partition. Performing Access Control... delete that VISTA User number from the list below for the access point-related event desired.
See "Setting Up Access Groups" in...
User Guide - Page 28
... Access Control Card Functions (cont'd)
↓ VISTA Card ID Number
001 Exec Priv?
however, only executive privilege assigned to provide the cardholder with executive privilege from the access group;
Press 1 to a card will be inherited from gaining access through access points only if the following conditions exist:
• The access point has been programmed to an access...
User Guide - Page 41
... near the end of a time window controlling an access point, the access point will overwrite your system. listed in your existing time-driven events. • Action codes 60 (AP Exit Only), 66 (AP Group Exit Only), or 72 (AP Partition Exit Only) disable the entry reader at set via a keypad command or event) to protect the...
Honeywell VISTAKEY Reviews
We have not received any reviews for Honeywell yet.