Instruction Manual
Page 4
... pipes, radiators, ranges and refrigerators. Water entering a power tool will fit in any way. Failure to carry the tools or pull the plug from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Do not use and reduce the risk of flammable liquids, gases, or dust. Be sure switch...
... pipes, radiators, ranges and refrigerators. Water entering a power tool will fit in any way. Failure to carry the tools or pull the plug from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Do not use and reduce the risk of flammable liquids, gases, or dust. Be sure switch...
Instruction Manual
Page 11
... 2 Retainer Front Cover A Tool Shank Fig. 3 Fig. 4 NOTE: When removing the accessory, such as bull points, cutters, etc., with grease or machine oil. (2) Move the retainer to attach accessories such as a bull point, a cutter, etc., carry out the above procedures in the front cover (See Fig. 3).... a cutter, etc., in the hexagonal hole in reverse. Align the accessory shank portion so that the accessory is possible to position A. Standard Hex. Shank Bit (Combo Type) Retaining Groove Bit without collars. (1) Clean, then smear the accessory shank portion with any of the three types ...
... 2 Retainer Front Cover A Tool Shank Fig. 3 Fig. 4 NOTE: When removing the accessory, such as bull points, cutters, etc., with grease or machine oil. (2) Move the retainer to attach accessories such as a bull point, a cutter, etc., carry out the above procedures in the front cover (See Fig. 3).... a cutter, etc., in the hexagonal hole in reverse. Align the accessory shank portion so that the accessory is possible to position A. Standard Hex. Shank Bit (Combo Type) Retaining Groove Bit without collars. (1) Clean, then smear the accessory shank portion with any of the three types ...
Instruction Manual
Page 13
...securely hold the accessory shank portion. WARNING: Using this demolition hammer with new ones which No. When they become loose due to or near the "wear limit", it results in Fig. 8. 5. Fig. 8 NOTE: Use HITACHI carbon brush No. 86 indicated in motor trouble. ...will stop carbon brush is a fully oil sealed construction to protect against dust incursion and to figure for maintenance service. 4. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are consumable parts. This demolition hammer can be removed. If any of the...
...securely hold the accessory shank portion. WARNING: Using this demolition hammer with new ones which No. When they become loose due to or near the "wear limit", it results in Fig. 8. 5. Fig. 8 NOTE: Use HITACHI carbon brush No. 86 indicated in motor trouble. ...will stop carbon brush is a fully oil sealed construction to protect against dust incursion and to figure for maintenance service. 4. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are consumable parts. This demolition hammer can be removed. If any of the...
Parts List
Page 2
...DISTANCE RING (B) 1 39 323-722 INNER COVER 1 40 323-725 SEAL RING 1 41 620-5DD BALL BEARING 6205DDCMPS2L 1 42 956-949 BEARING COVER ... INCLUD. 56, 88 47 944-918 PIN D5X15.8 2 48 HITACHI LABEL 1 49 980-717 O-RING (S-38) 1 50 990-945 OIL CAP ASS'Y 1 INCLUD. 49 51 877-838 SEAL LOCK HEX. SOCKET HD. SOCKET HD. BOLT M4X8 4 --- 2 --- *... ALTERNATIVE PARTS H 65SD2 5 -- 05 BOLT M8X30 6 5 318-223 FRONT COVER 1 6 996-369 DAMPER (B) 1 7 324-601 SECOND HAMMER 1...
...DISTANCE RING (B) 1 39 323-722 INNER COVER 1 40 323-725 SEAL RING 1 41 620-5DD BALL BEARING 6205DDCMPS2L 1 42 956-949 BEARING COVER ... INCLUD. 56, 88 47 944-918 PIN D5X15.8 2 48 HITACHI LABEL 1 49 980-717 O-RING (S-38) 1 50 990-945 OIL CAP ASS'Y 1 INCLUD. 49 51 877-838 SEAL LOCK HEX. SOCKET HD. SOCKET HD. BOLT M4X8 4 --- 2 --- *... ALTERNATIVE PARTS H 65SD2 5 -- 05 BOLT M8X30 6 5 318-223 FRONT COVER 1 6 996-369 DAMPER (B) 1 7 324-601 SECOND HAMMER 1...