HP V213a Support and Manuals
Popular HP V213a Manual Pages
User Guide - Page 3
... harm or loss of information.
Text set off in this manner indicates that failure to equipment or loss of life. NOTE: Text set off in this manner provides important supplemental information. WARNING!
ii
About This Guide
This guide provides information on setting up the monitor, installing drivers, using the on-screen display menu, troubleshooting and technical specifications.
User Guide - Page 4
Setting Up the Monitor
Unpacking the Monitor 4 Installing the Monitor 4 Connecting Monitor Cables 7 Connecting the Audio Cable 7 High-Bandwidth Digital Content Protection (HDCP 8 Connecting the Power Cable 8 Adjusting the Tilt 9
4. Table of Contents
About This Guide
1. Troubleshooting
Solving Common Problems 19 Getting Support from the Internet 10
Front-Panel Controls 11 ...
User Guide - Page 5
... security cable (security cable sold separately) • Plug and Play capability, if supported by your computer system • On-Screen Display (OSD) adjustments in several languages for your product, go to the Product Notices provided on screen instructions. HP LCD Monitors 1 1. Select Drivers & Downloads, and then follow the on your media disc, if one is...
User Guide - Page 6
... can replace the equipment, if surge protection fails.
It describes proper workstation, setup, posture, and health and work habits for this ability. the power strips must be specifically labeled as a power strip or Uninterruptible Power Supply (UPS).
Arrange them . Do not pull on the documentation CD, if one is included with the monitor. This guide...
User Guide - Page 7
...provided for each device.
• Install the monitor near a power outlet that are covered in the operating instructions.
Clean the monitor plastics with a clean cloth dampened...monitor by pulling the cord.
• Turn the monitor off the monitor and the computer.
2. If the monitor is not operating properly or has been dropped or damaged, contact an authorized HP dealer, reseller, or service...
User Guide - Page 8
.... Prepare a flat area to the LCD screen; Preparing the monitor for installation. Setting Up the Monitor
ENWW Make sure all contents are included. 3. Setting Up the Monitor
Unpacking the Monitor
1.
doing so can install the monitor on a flat, soft, protected table or desk surface
with the support column overhanging the edge. Store the packing box. 2. CAUTION: The screen is...
User Guide - Page 10
4. Follow the instructions included with the monitor.
6 Chapter 3. CAUTION: This monitor supports the VESA industry standard 100 mm mounting holes. It is important to verify that the manufacturer's mounting solution is compliant with the VESA standard for screws to be used because they may damage the monitor.
NOTE: This apparatus is rated to the back of the monitor display...
User Guide - Page 12
... (HDCP)
Your monitor supports HDCP and can receive high-definition content.
WARNING! To reduce the risk of electric shock or damage to display protected content. Setting Up the Monitor
ENWW If you do one end of the following if a properly grounded electrical outlet is not likely to a grounded electrical outlet. See"Technical Specification" (Appendix B) for...
User Guide - Page 14
... Windows® operating system documentation for instructions (in your monitor and click Go. 5. Installing the monitor driver software from the CD
To install the monitor driver software from the HP Support site: 1. Select the language. 3.
NOTE: You might need to install the digitally signed monitor drivers (INF or ICM files) manually from the Internet. Select your computer. Ensure...
User Guide - Page 18
...Set to : • Top • Middle • Bottom • Off
The factory default is On.
Select: • On • Off
The factory default is On. Turns off the power LED on select models...Recall Mode Display
Monitor Status
DDC/CI Support
Bezel Power LED Volume
Description
Adjust to control some OSD menu features such as brightness, contrast and color temperature. Sets the time ...
User Guide - Page 19
Provides the recommended resolution mode and refresh rate for the monitor. Reports the firmware version of backlight operation. VGA is On.
The monitor will automatically determine the video format. Exits the OSD menu screen.
http://www.hp.com/support
Returns all OSD menu settings and DDC/CI controls to two active and valid video sources.
The factory...
User Guide - Page 21
... is off, and the Power light is connected to "Technical Specification" (Appendix B). When the monitor is controlled by the computer. Set the main Clock settings correctly first, because the Phase settings depend on the main Clock settings.When adjusting the Clock and Phase values, if the monitor images become distorted,continue adjusting the values until the distortion...
User Guide - Page 23
... capable of your are bent.
No Plug & Play
• In order for the Plug & Play feature of the pins are bent.
• Make sure the HP Monitor Drivers are installed (HP Monitor Drivers are available at the resolution your computer. Missing one of the primary colors (RED, GREEN, or BLUE)
• Inspect the...
User Guide - Page 24
... numbers when contacting HP about your monitor. For technical support contact information, refer to the printed documentation included with the monitor. The rating label is on invoice • Conditions under which the problem occurred • Error messages received • Hardware configuration • Name and version of the monitor.
20 Appendix A. Troubleshooting
ENWW Preparing to...
User Guide - Page 27
... ability to help guarantee trouble-free performance. This is common to the HP Web site at a supported resolution and refresh rate, from a distance of the two. These imperfections are made. A defective whole pixel is always turned on (a bright spot on a dark background), or it is not specific to your LCD Monitor, refer to all vendors...
HP V213a Reviews
Do you have an experience with the HP V213a that you would like to share?
Earn 750 points for your review!
We have not received any reviews for HP yet.
Earn 750 points for your review!