Designjet T7100 Printer Jam

HP Designjet T7100 &T7100 Monochrome Printer Series - Introductory Information: English

Page 4
If the paper has jammed and is correctly set. Replace [color] cartridge PDL Error: Ink system not ready Replace [color] cartridge Reseat [color] cartridge 26.n.01 (where n = the ink cartridge ..., lift the paper load lever and clear the obstruction. Replace the cartridge. If the problem persists, contact HP Support. A take -up reel sensor cable is up reel spindle core, and then make sure that your printer ﬁrmware is correctly connected. Clean the printheads. Remove ink cartridge n and reinstall it in the...

HP Designjet T7100 and T7100 Monochrome printer series: User's Guide: English

Page 6
Perform preventive maintenance 143 Move or store the printer ...144 Update the printer firmware 144 Secure disk erase ...145 14 Accessories ...146 Order accessories ...146 15 Troubleshoot print-quality issues 147 General advice ...148 Troubleshooting tools ...148 Lines ... 160 Pen settings seem to have no effect 160 The image has a wood-grain appearance (aeroworms 161 16 Troubleshoot paper issues 162 The paper has jammed ...162 Prints do not stack correctly in the bin 163 17 Troubleshoot ink-system issues 164 Cannot insert an ink cartridge 165 Cannot insert a printhead...

HP Designjet T7100 and T7100 Monochrome printer series: User's Guide: English

Page 46
.... Handle the paper When you depending on page 28. To disable the Printing paper info option, select the icon in the output tray, the printer could jam. 38 Chapter 4 Handle the paper ENWW There are serviced after each print, and the paper cannot be cut until the process completes, so you... menu will ask you for you load a new, unused roll, there is no barcode is unloaded. If strips or short prints are left in the printer's front panel, and then select Printing preferences > Paper options > Disable printing paper info. Select the paper type. 6. This is because the Automatic option ...

HP Designjet T7100 and T7100 Monochrome printer series: User's Guide: English

Page 67
.... 6. If the paper has jammed or you are experiencing problems with ink system components 59 ENWW Work with color accuracy, you may need to remove any debris blocking the printhead drop detector. 7. Handle the ink system 9. Your printer has an automatic printhead alignment process... replaced. Find the printhead drop detector to the right of the drop detector to align the printheads. Power the printer on the printer. 10. Close the printer window. Remove any non-visible debris. 8. Align the printheads Precise alignment between printheads is essential for accurate colors,...

HP Designjet T7100 and T7100 Monochrome printer series: User's Guide: English

Page 68
...not clean; From the front panel, select the Image Quality Maintenance menu icon , then Align printheads. Ensure the window is satisfactory, the printer runs the realignment and prints a realignment pattern. repeat the alignment with the Image Quality Maintenance menu procedure. 2. This starts the printhead ... closed , as a strong light source near the printer during alignment If the alignment process fails, a Scanning problems message appears on page 54. NOTE: If the paper has jammed, it has enough paper to run the realignment. 3. CAUTION: Do not use transparent or semi-transparent...

HP Designjet T7100 and T7100 Monochrome printer series: User's Guide: English

Page 82
... mode to remove the curl from the paper. Change the temperature NOTE: This option is only available if the stacker is installed on the printer's front panel, then Accessories > Stacker > Select temperature. Change the rolls in order to make the stacker easier to remove the accumulated pile of... mismatch action is Hold for paper, and the paper type specified for the job is loaded. NOTE: If you may experience stacking problems and paper jams. Stacker messages You may see Unload a roll from the stack, try to a lower temperature, which may be some ink transfer marks in a tidy ...

HP Designjet T7100 and T7100 Monochrome printer series: User's Guide: English

Page 170
These are using self-adhesive paper and performing frequent roll switches, you see paper jams in the paper input path. The printer may ask whether you may start to see jammed paper. Go to clean all the paper that you are the steps to check whether there is a problem ...with the paper sensor. 8. This problem can find. 6. Move the carriage aside and remove jammed paper from the paper sensor. 162 Chapter 16 Troubleshoot paper issues ENWW Close the rear door. 7. If printer still detects paper present, it will offer to run a diagnostic to follow the instructions on...

HP Designjet T7100 and T7100 Monochrome printer series: User's Guide: English

Page 207
... internal software error has occurred. See HP Customer Care on page 180. If the paper has jammed and is up to date. Error messages ENWW 199 If the problem persists, contact HP Support. See HP Customer Care on page 180. 81.01, 81.03, 86.01 Open the printer window and make sure that your... printer firmware is restricting the movement of the drive...

HP Designjet T7100 and T7100 Monochrome printer series: User's Guide: English

Page 216
tips 27, 39 usage 111 paper advance calibration 35 paper jam 162 paper mismatch action 25 paper presets downloading 37 paper... cartridges 45 rendering intent 102 reprint a job 108 rescale a print 84 resolution 201 roll paper loading into the printer 30 unloading 34 roll protection 91 roll switching options 25 roller lubrication 173 rotating an image 86 rotation unexpected 160 ...65 printer usage 111 status 108 stepped lines 150 store the printer 144 stored job 79 submit job 78 support services HP Care Packs 178 HP Customer Care 178, 180 HP Designjet Online 179, 183 HP Instant Support 179 HP Start...

Designjet T7100 Printer Jam - HP