Designjet T120 Roll Cover

HP Designjet T120 and T520 ePrinter Series - User's Guide

Page 12
...covers the following printer models, normally referring to them by their short names for printing high-quality images on paper up to 2400 × 1200 dpi (T520) or 1200 × 1200 dpi (T120... ● Includes Web-connected features such as automatic firmware upgrades, HP Designjet ePrint & Share, and HP ePrint ● Handles roll and cut-sheet paper, with a multi-sheet tray ● Color... T120 T520-24 T520-36 The printer's main features Your printer is a color inkjet printer designed for brevity. Full name HP Designjet T120 24-in ePrinter HP Designjet T520 24-in ePrinter HP Designjet...

HP Designjet T120 and T520 ePrinter Series - User's Guide

Page 14
Power socket 4. Blue stop 2. Paper roll 6 Chapter 1 Introduction ENWW Rear view (T520) 1. Roll cover 2. Multi-sheet tray Rear view (T120) 1. Spindle 3. Communication ports 3.

HP Designjet T120 and T520 ePrinter Series - User's Guide

Page 41
... widths. The spindle has a stop can be removed to hold rolls of the spindle. 4. If your fingers into the spindle supports during the removal process. 3. If the roll is a T520, open the roll cover. 2. ENWW Load a roll onto the spindle 33 Remove the blue paper stop from the printer.... Do not insert your printer is long, rest the spindle horizontally on a table and load the roll on the table.

HP Designjet T120 and T520 ePrinter Series - User's Guide

Page 43
If your fingers inside the printer's paper path. The blue hub should be on the left, as viewed from the front of the paper into the printer. If the edge of the roll), pull the paper slightly and cut a straight edge. 5. Do not push your printer is not straight or torn (sometimes due to tape used to hold end of the roll is a T520, open the roll cover. 3. ENWW Load a roll into the printer, holding it by both ends. 2. WARNING! Insert the spindle into the printer 35 Insert the edge of the printer. 4.

HP Designjet T120 and T520 ePrinter Series - User's Guide

Page 44
... and the paper flexes slightly. If you still cannot find your paper type in the whole list, see The paper type is a T520, close the roll cover. NOTE: If you to the core, the front panel asks you have an unexpected issue at any stage of the paper is not correctly aligned... More paper types. If your paper type in the printer. 36 Chapter 5 Paper handling ENWW 6. After unloading, the multi-sheet tray is paper on the roll, you do not see The paper cannot be loaded successfully on page 98. 8. The printer checks the alignment and measures the width.

HP Designjet T120 and T520 ePrinter Series - User's Guide

Page 45
... from the multi-sheet tray. 1. ENWW Load a single sheet 37 If you have to wait while it is a T520, open the roll cover. 5. NOTE: Sheets of the input slot. If a roll is already loaded, you do not see The paper type is not in the front panel, press More paper types. If your...

HP Designjet T120 and T520 ePrinter Series - User's Guide

Page 48
... than zero, the printer does not cut sheets covered and clean or brush them before handling. TIP: To cut roll paper while the automatic cutter is dry before loading them in the output tray and marks on loading and unloading rolls. If the dry time is displayed. Turn the...the printer cuts the paper and then performs the printhead maintenance. Maintain paper To maintain paper quality, follow the recommendations below. ● Store rolls covered by another piece of higher importance or when you cancel the drying time during a print, the printer may wish to change the cutter ...

HP Designjet T120 and T520 ePrinter Series - User's Guide

Page 104
... become loose around the core, the printer cannot load the paper. This may be necessary even with the reference line on the roll cover. ● Do not attempt to straighten the sheet during the loading process, unless instructed to start the load process again, cancel the process on ... hand-cut sheets, which may have been removed. ● Check that the paper is far enough inside the printer, you . ● Check that all roll end plugs have irregular edges. Use only purchased sheets. If the paper has not been inserted straight, follow the instructions given on the front-panel...

HP Designjet T120 and T520 ePrinter Series - User's Guide

Page 108
Open the top cover. 2. The roll has jammed When a paper jam occurs, you can lift up and out from the top of the way. 3. Try to move the printhead carriage out ...

HP Designjet T120 and T520 ePrinter Series - User's Guide

Page 109
Open the roll cover and rewind the roll. The multi-sheet tray has jammed If the paper in the multi-sheet tray has jammed, proceed as it could damage the printer. 4. Close the top cover. 5. You may need to handle. You may feel resistance if the paper is still some paper ...causing an obstruction within the printer, restart the procedure and carefully remove all pieces of paper. pull firmly. 6. Reload the roll, or load a new sheet; ENWW...

HP Designjet T120 and T520 ePrinter Series - User's Guide

Page 122
... print has vertical bands of different colors along it to Quality. Try using thicker paper, choosing from the recommended paper types such as HP Heavyweight Coated Paper. Try using higher print-quality settings (see Printing on page 42. To avoid this problem: 1. See Printing on page...2. Edges of objects are inaccurate 114 Chapter 13 Troubleshooting print-quality issues ENWW See Order paper on the print. Always keep the cover of your paper rolls and sheets by storing them in the driver dialog, select the custom print-quality options, and try setting it : 1. Protect your...

Designjet T120 Roll Cover - HP