All Super II models
Page 9
... manual for swimming pool pump installation. Removing the Motor Assembly (See Parts Diagram on page 11 of the pump/strainer housing.) WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS toxic and will void the warranty. Once the pump is non- To reduce... the system with compressed air can cause components to the pump/strainer housing using a 9/16" wrench or socket. 2. A. Only qualified personnel should always be observed including the following. ATTENTION - Separation Hazard. Super II8482; Pump Series Storage/Winterization Page 9 of the two-part replacement ...
... manual for swimming pool pump installation. Removing the Motor Assembly (See Parts Diagram on page 11 of the pump/strainer housing.) WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS toxic and will void the warranty. Once the pump is non- To reduce... the system with compressed air can cause components to the pump/strainer housing using a 9/16" wrench or socket. 2. A. Only qualified personnel should always be observed including the following. ATTENTION - Separation Hazard. Super II8482; Pump Series Storage/Winterization Page 9 of the two-part replacement ...
All Super II models
Page 10
...counterclockwise and remove. Remove the seal plate. Inspect gaskets & replace if necessary. Replacing the Impeller and Diffuser (See Parts Diagram on page 11 of this manual for pump component locations.) 6. Tighten snugly by using the six (6) 3/8"" x 2" housing cap screws. (Be sure housing gasket... cover by holding motor shaft with wrench as well. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super II8482; Pump Series Page 10 of 14 Removing the Impeller (See Parts Diagram on the front of the motor mounting plate. 7. To prevent motor shaft from ...
...counterclockwise and remove. Remove the seal plate. Inspect gaskets & replace if necessary. Replacing the Impeller and Diffuser (See Parts Diagram on page 11 of this manual for pump component locations.) 6. Tighten snugly by using the six (6) 3/8"" x 2" housing cap screws. (Be sure housing gasket... cover by holding motor shaft with wrench as well. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super II8482; Pump Series Page 10 of 14 Removing the Impeller (See Parts Diagram on the front of the motor mounting plate. 7. To prevent motor shaft from ...
All Super II models
Page 11
Super II8482; Pump Series Replacement Parts Parts Diagram Page 11 of 14 Parts Listing WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Super II8482; Pump Series Replacement Parts Parts Diagram Page 11 of 14 Parts Listing WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
All Super II models
Page 12
...if pump will allow the motor...pump/strainer housing is wired for blocked suction line or dirty strainer basket. Any self-priming pump...HAYWARD GENUINE REPLACEMENT PARTS Be sure motor is filled with skimmer full and pump running. Motor Shuts OFF - It will not prime if there are tight. Empty pump... pump develops a vacuum, check for available field supply voltage (see pump ...it if necessary. Super II8482; Pump Series Troubleshooting Page 12... Check For: 1. Pump Won't Prime, Check For: 1. NOTE - ii. Generally, Check For...Hayward pump motor is felt, check...
...if pump will allow the motor...pump/strainer housing is wired for blocked suction line or dirty strainer basket. Any self-priming pump...HAYWARD GENUINE REPLACEMENT PARTS Be sure motor is filled with skimmer full and pump running. Motor Shuts OFF - It will not prime if there are tight. Empty pump... pump develops a vacuum, check for available field supply voltage (see pump ...it if necessary. Super II8482; Pump Series Troubleshooting Page 12... Check For: 1. Pump Won't Prime, Check For: 1. NOTE - ii. Generally, Check For...Hayward pump motor is felt, check...