Haier HB6000VD1M22-P Support and Manuals
Get Help and Manuals for this Haier item
This item is in your list!
View All Support Options Below
Free Haier HB6000VD1M22-P manuals!
Problems with Haier HB6000VD1M22-P?
Ask a Question
Free Haier HB6000VD1M22-P manuals!
Problems with Haier HB6000VD1M22-P?
Ask a Question
Popular Haier HB6000VD1M22-P Manual Pages
User Manual - Page 1
... MECHANICAL CODE
READ THESE INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING TO INSTALL OR SERVICE THIS APPLIANCE.
Installation & Operation Manual Air Handler
13 SEER 2 3 4 5 Ton
WARNING WHEN THIS APPLIANCE IS INSTALLED IN AN ENCLOSED AREA, SUCH AS A GARAGE OR UTILITY ROOM, WITH ANY CARBON MONOXIDE PRODUCING DEVICES (i.e.
These instructions should be retained and kept adjacent to change...
User Manual - Page 2
...Replacement Parts Source Installation Requirements Air Flow Orientation Horizontal Left-Hand Instructions Refrigerant Tubing Condensate Removal Electrical Connections Thermostat Wiring Orifice Change Circulating Air Duct Blower Performance Start-up Regular Maintenance Model... transportation company. Should questions arise contact the local EPA office. This appliance is approved for installation in...
User Manual - Page 4
PHYSICAL DIMENSIONS of 3 Ton
PLASTIC BREAKER COVER
INLET BOTTOM SIDE VIEW ELECTRICAL POWER SUPPLY
SUCTION LINE LIQUID LINE
LOW VOLT SUPPLY
ELECTRICAL POWER SUPPLY
4
User Manual - Page 5
PHYSICAL DIMENSIONS of 4,5 Ton
PLASTIC BREAKER COVER
INLET BOTTOM SIDE VIEW ELECTRICAL POWER SUPPLY
SUCTION LINE LIQUID LINE
LOW VOLT SUPPLY
ELECTRICAL POWER SUPPLY
5
User Manual - Page 6
...6 When more than one appliance is designed for service or replacement must be installed with a separate drain line properly sloped and terminated...installer and placed under the entire unit with the ignition source at least 18" above the floor level. REPLACEMENT PARTS SOURCE Replacement parts are available through local distributors.When ordering replacement parts, give the COMPLETE model...
User Manual - Page 7
...
*Horizontal Right Discharge Tube and Drain conn. front (see page 6) Important: Remove the horizontal pan when unit is installed in unconditioned i.e. (Garage, Attic ) application, or downflow applications, and install insulation kit on vertical ( donut shape ) drain pan.
*Upflow Discharge *Air Handler is factory ready for Upflow & Horizontal Right Discharge Application for 3*4*5 as shown...
User Manual - Page 8
... be provided by pouring water into channel bracket at the rear of air pressure. Plastic Drain cover
Fig.1
oval gasket
WARNING: If incorrect knockouts are removed, flooding will cancel product warranty. Before setting up flowrator assembly for proper drainage by the installer and placed under the entire unit with the horizontal drain pan...
User Manual - Page 9
...tubing size. The unit and the auxiliary drain pan must be adequately elevated to the air handler. Use of a condensate removal pump is permitted when necessary.This condensate pump should... insulated. The condensate trap must be supported or routed to avoid undue stress. When using copper tubing as a condensate line adequate caution muat be installed as measured in inches of water, ...
User Manual - Page 10
...the electrical requirements for that kit.
Wiring selection must be installed within sight of copper connections are recommended inside the control box (see UL 1995, section 37.9). Copper wire is recommended for "HB" air handlers installed without a heat kit.
10 Model No.
2 Ton 3 Ton 4 Ton 5 Ton
5 Ton -E
Min. ELECTRICAL CONNECTIONS
The required electrical power supply information is...
User Manual - Page 11
...For Thermostat only control Air
Diagram 1
Conditioning open /stop , hot control Environment temperature, can adopt different power switch show diagram 2. R : AC24V
TERMOSTAT
Y : COMPRESSOR
G
O
Y
R
C
G : FAN
O : 4 -WAY VALUE
TO INDOOR
For detailed Thermostat, please connect FAN RELAY
CONTROL
corresponding terminal according to above
control specification. Thermostat can adopt multi...
User Manual - Page 12
... power switch
show diagram 5.
Note: Thermostat C: COM. R : AC24V
TERMOSTAT
Y : COMPRESSOR
G
Y
R
C
G : FAN
For detailed Thermostat, please connect corresponding terminal according to above control specification. This mode is
control the indoor unit & cooling
only outdoor unit at the same time no air supply mode. TO FAN RELAY CONTROL RD
BL
CY TO OUTDOOR UNIT C,Y
RD
BL
24V...
User Manual - Page 13
... the outdoor condenser, the orifice must be designed and installed as per local and/or national code.Refer to NFPA 90A & 90B and the National Environmental Systems Contractors Association Manual "K". The restrictor (orifice) should be changed to match the outdoor unit capacity.
standards.
FOLLOW THESE INSTRUCTIONS TO PREVENT INJURY:
1) Remove the 1/4 nut on the liquid...
User Manual - Page 14
... heat mode. 3) Measure the return air temperature. 4) Measure the supply temperature. BLOWER PERFORMANCE CFM versus Static Pressure (inches of water column dry coil w/ filter) 4% reduction for differences encountered in various locations
to obtain an average. 5) Subtract the return temperature from the supply temperature.
Model
Static Pressure
0.1
CFM
0.15 0.2
2 Ton
High 900 877 856...
User Manual - Page 15
... with water. Return air is elevated when installed in place and secured. Low voltage wiring is installed, when necessary, and pitched to allow for drainage. A certified service technician should be elevated, trapped and pitched to allow for drainage. All panels must be leak free. Auxiliary drain is connected. Unit is cleaned or replaced. Tubing should...
Haier HB6000VD1M22-P Reviews
Do you have an experience with the Haier HB6000VD1M22-P that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Haier yet.
Earn 750 points for your review!