Manual
Page 57
...chip. (Default: Enabled) - 57 - Example: Part1-2 Status = Short / Length = 2m Explanation: A fault or short might occur at a normal speed of 10/100/1000 Mbps in Windows mode or when the LAN Boot ROM is the approximate length of the attached LAN cable. Onboard LAN1/2 Boot ROM Allows you to...Normally... SMART LAN1/2 (LAN Cable Diagnostic Function) CMOS Setup Utility-Copyright (C) 1984-2009 Award Software SMART LAN Start detecting at a speed of 10/100 Mbps in MS-DOS mode; This feature will only operate at Port..... Note: The Gigabit hub will detect cabling issue and report the ...
...chip. (Default: Enabled) - 57 - Example: Part1-2 Status = Short / Length = 2m Explanation: A fault or short might occur at a normal speed of 10/100/1000 Mbps in Windows mode or when the LAN Boot ROM is the approximate length of the attached LAN cable. Onboard LAN1/2 Boot ROM Allows you to...Normally... SMART LAN1/2 (LAN Cable Diagnostic Function) CMOS Setup Utility-Copyright (C) 1984-2009 Award Software SMART LAN Start detecting at a speed of 10/100 Mbps in MS-DOS mode; This feature will only operate at Port..... Note: The Gigabit hub will detect cabling issue and report the ...
Manual
Page 71
... setup disk. A. Step 2: Click New. (Note) Xpress Recovery2 checks the first physical hard drive in advanced (10 GB or more is recommended; Installing Windows Vista and Partitioning the Hard Drive Step 1: Click Drive options. For example, when hard drives are attached to the first and... and Xpress Recovery2 are not supported. System Requirements: • At least 512 MB of system memory • VESA compatible graphics card • Windows XP with Xpress Recovery cannot be restored using Xpress Recovery2. • USB hard drives are not supported. • Hard drives in RAID/AHCI ...
... setup disk. A. Step 2: Click New. (Note) Xpress Recovery2 checks the first physical hard drive in advanced (10 GB or more is recommended; Installing Windows Vista and Partitioning the Hard Drive Step 1: Click Drive options. For example, when hard drives are attached to the first and... and Xpress Recovery2 are not supported. System Requirements: • At least 512 MB of system memory • VESA compatible graphics card • Windows XP with Xpress Recovery cannot be restored using Xpress Recovery2. • USB hard drives are not supported. • Hard drives in RAID/AHCI ...
Manual
Page 102
... Non-RAID Solve Mirror Conflict Rebuild Mirror Drive Save And Exit Setup Exit Without Saving Gigabyte Technology Corp. When prompted to confirm your settings before exiting the RAID BIOS utility, then press (Figure 10). [ Main Menu ] Create RAID Disk Drive Delete RAID Disk Drive Revert HDD to...RAID WILL LOST!! Y Model Name RAID Level Capacity Status RDD0: GRAID 0-Stripe 240 GB Normal Members(HDDx) 01 [fgTAB]-Switch Window [hi]-Select ITEM Figure 10 [ENTER]-Action [ESC]-Exit Now, you may proceed to Non-RAID Solve Mirror Conflict Rebuild Mirror Drive Save And Exit Setup Exit...
... Non-RAID Solve Mirror Conflict Rebuild Mirror Drive Save And Exit Setup Exit Without Saving Gigabyte Technology Corp. When prompted to confirm your settings before exiting the RAID BIOS utility, then press (Figure 10). [ Main Menu ] Create RAID Disk Drive Delete RAID Disk Drive Revert HDD to...RAID WILL LOST!! Y Model Name RAID Level Capacity Status RDD0: GRAID 0-Stripe 240 GB Normal Members(HDDx) 01 [fgTAB]-Switch Window [hi]-Select ITEM Figure 10 [ENTER]-Action [ESC]-Exit Now, you may proceed to Non-RAID Solve Mirror Conflict Rebuild Mirror Drive Save And Exit Setup Exit...
Manual
Page 114
...and browse to load the driver. Note: For users using a SATA optical drive, be detected at this stage), select Load Driver (Figure 9). Appendix Figure 10 - 114 - Figure 9 Step 2: Insert the motherboard driver disk (Method A) or the floppy disk/USB flash drive that below appears (RAID/AHCI hard... drive(s) will not be sure to copy the driver files from the Windows Vista setup disk and perform standard OS installation steps. For the JMicron JMB362/GIGABYTE SATA2: Step 1: Restart your system and browse to the following directory: \BootDrv\GSATA\32Bit For...
...and browse to load the driver. Note: For users using a SATA optical drive, be detected at this stage), select Load Driver (Figure 9). Appendix Figure 10 - 114 - Figure 9 Step 2: Insert the motherboard driver disk (Method A) or the floppy disk/USB flash drive that below appears (RAID/AHCI hard... drive(s) will not be sure to copy the driver files from the Windows Vista setup disk and perform standard OS installation steps. For the JMicron JMB362/GIGABYTE SATA2: Step 1: Restart your system and browse to the following directory: \BootDrv\GSATA\32Bit For...