Gigabyte GA-K8VT800 Pro Support and Manuals
Get Help and Manuals for this Gigabyte item
View All Support Options Below
Free Gigabyte GA-K8VT800 Pro manuals!
Problems with Gigabyte GA-K8VT800 Pro?
Ask a Question
Free Gigabyte GA-K8VT800 Pro manuals!
Problems with Gigabyte GA-K8VT800 Pro?
Ask a Question
Popular Gigabyte GA-K8VT800 Pro Manual Pages
Manual - Page 2
...
drives with identical model and capacity).
Ác
Configuring IDE RAID Hard Drive(s) (Controller GigaRAID (IT8212))
Åé
¤¤
To set up IDE RAID hard drive(s), follow the steps below
¤å
(1) Install IDE hard drive(s) in your computer.
(2) Configure GigaRAID controller mode and boot sequence in BIOS Setup.
(3)* Configure RAID set in your system...
Manual - Page 4
...
F7: Optimized Defaults
Step 4 Save and exit BIOS Setup. IDE RAID Drives Configuration (GigaRAID) - 4 - SCSI-0: IT8212 (Figure 2).
¤å
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
Hard Disk Boot Priority
Step 3
Figure 2
Set First Boot Device to CD-ROM so you want to install
¤¤
Microsoft Windows 2000/XP and use the...
Manual - Page 14
... RAID Drives Configuration (GigaRAID) - 14 -
Ác
(4) Making a IDE RAID controller driver disk
Åé
To install Windows 2000/XP onto a hard drive on the GigaRAID controller successfully, you need to install required driver for the GigaRAID controller on your motherboard during the Windows setup process.
¤å
First of all, you need to copy the...
Manual - Page 12
... Controller USER'S MANUAL
Totally, there are sent to set as array 0. All the hard drives attached on the controller will be set a RAID 0 (stripe) array. Selecting RAID 0 can increase data transfer rate and allow the best overall performance characteristics because of disks needed 2 or 3 or 4 2 4 2 or 3 or 4 1 or 2 or 3 or 4
Setup Array for RAID...
Manual - Page 38
...) ATA RAID Controller has already been properly setup in "D:\BootDrv\menu.exe" 4) Information on all chipsets should be installed under the following various operating systems. Before starting to install the RAID drivers. After that hard drive. GigaRAID (IT8212) ATA RAID Controller USER'S MANUAL
Driver Installation
This section details the procedures to install the GigaRAID (IT8212) ATA RAID...
Manual - Page 52
If there is a marking ! or ? User should remove the device and reinstall.
52 under SCSI and ATA RAID Controller device, it
indicates that the driver has not been correctly installed. GigaRAID (IT8212) ATA RAID Controller USER'S MANUAL 3.
Manual - Page 1
Table of Contents
Configuring SATA Hard Drive(s) (Controller: VIA VT8237/VT8237R 2 (1) Installing SATA hard drive(s) in your computer 2 (2) Configuring SATA controller mode and boot sequence in BIOS Setup 3 (3) Configuring RAID set in RAID BIOS 5 (4) Making a SATA Driver Disk 10 (5) Installing SATA controller driver during OS installation 12
Manual - Page 12
...driver disk and configured BIOS settings, you see the "Press F6 if you need to install a 3rd party SCSI or RAID driver. Windows Setup
Setup could not determine the type of one or more mass storage devices installed...to manually specify an adapter.
After
pressing F6, there will load support for the following is an example of some files being loaded before you are ready to install ...
Serial ATA manual - Page 5
...Master & Slave
Revision 1.01, May 19, 2003
3
Installing The Hard Drives Number of the same model and capacity is recommended. Two SATA + Two PATA Configuration:
VT6420 supports two "Master" SATA hard disk drives and one "...Only SATA hard disk drive supports RAID, so it supports RAID 0, RAID 1, and JBOD. Please connect SATA hard disk drivers according to the following two configurations: 1.
Serial ATA manual - Page 17
... INSTALLATION
Microsoft Windows Driver Installation
1. Revision 1.01, May 19, 2003
15
Driver and RAID Software Installation After Windows has finished booting up, the system will automatically find the newly installed adapter and prompt the Found New Hardware Wizard window. Click Cancel to begin the driver and software installation. Browse the CD or diskettes and double click on setup...
User Manual - Page 15
... on the power supply or connect the power cable to the power outlet. Hardware Installation Process Installing Expansion Cards Step 4- English
Chapter 2 Hardware Installation Process
To set up your computer, you must complete the following steps:
Step 1-
You have accomplished the hardware installation! Installing Processor and CPU Cooling Fan Step 2- Continue with the BIOS/software...
User Manual - Page 22
...contact your motherboard, please see the following descriptions for 2-/4-/6-channel audio setup installation, please refer to page 79. GA-K8VT800(Pro) Motherboard
- 22 - mouse and modem etc. If you may... Speaker) Line Out (Front Speaker) MIC In (Center and Subwoofer)
After install onboard audio driver, you want the detail information for the devices.
Please note: You are ...
User Manual - Page 28
... BIOS (either RAID or ATA133). If you wish to use IDE3 and IDE4, please use SATA0 and SATA1, please Enable " OnChip Serial ATA " item. Then, install the correct driver to the VT8237 SATA Manual at GIGABYTE's website.
(1) For GA-K8VT800 Pro only
1
7
SATA1
1
7
SATA0
Pin No. 1 2 3 4 5 6 7
Definition GND TXP TXN GND RXN RXP GND...
User Manual - Page 62
... 11: Password Setting
When you select this function, the following message will appear at the center of the screen to assist you to specify two separate passwords: SUPERVISOR PASSWORD and a USER PASSWORD. To disable password, just press when you try to confirm the password being disabled. A message "PASSWORD DISABLED" will appear to enter Setup.
(1) For GA-K8VT800 Pro only GA-K8VT800(Pro...
User Manual - Page 89
...NTFS format.
1. Technical Reference
2005/1/14, ¤U¤È 05:52 It supports FAT16 ¡BFAT32 ¡BNTFS format . 2. Award Modular BIOS v6.00PG, ...SETUP / Q-Flash, F9 For Xpress Recovery 08/16/2002-I845GE-6A69YG01C-00
F9 For Xpress Recovery
2. It must be set boot from CD-ROM Please go to use Xpress Recovery if you install Xpress Recovery immediately after installing O.S ,
drivers...
Gigabyte GA-K8VT800 Pro Reviews
We have not received any reviews for Gigabyte yet.