GE 45600 - Z-Wave Technology Wireless Lighting Remote Control Support and Manuals
GE 45600 Videos
Popular GE 45600 Manual Pages
User Manual - Page 1
45600
Wireless Lighting Control
Remote Manual
18 • Individual Z-Wave devices • Groups • Lighting scenes
Groups can include up to 232 devices
Scenes can include up to 32 devices
Compatible with all Z-WAVE products.
User Manual - Page 2
.../or scenes and control your lighting however secondary remotes cannot add or delete devices from your control network.
All other applications. Keep this remote is used to add or delete devices (lights / nodes) from different groups. INSTALLING BATTERIES Three "AAA" Alkaline batteries (not included) are interchangeable within the network can also set up and control up to 232 Z-Wave...
User Manual - Page 3
... compartment cover (located on the device so that can destroy electronic parts. • Dispose of the remote). 2. Replace the cover.
The remote retains all its information to a specific number key, perform the following steps: 1. Remove a node, group or scene can leak chemicals that it to the remote and Press LIGHT once. (Red LED blinks once) 4. Press LIGHT...
User Manual - Page 4
...blink, you wish to Groups and/or Scenes. Press REMOVE once. (Red LED ...controlled individually. Press a digit (1-9) for the device location you are trying to the remote and receives information from the remote. 6.
REMOVING AN INDIVIDUAL DEVICE (LIGHT / NODE) FROM YOUR REMOTE 1. If the device number you wish to your remote... and hold SETUP until both the red and green LEDs ...
User Manual - Page 5
... once. Repeat steps 1-5 if this occurs. CONTROLLING INDIVIDUAL LIGHTS (DEVICES / NODES) You can control a light to the
remote and receives information from the network. DELETING A DEVICE (LIGHT / NODE) FROM YOUR NETWORK To reset a device to its information to turn a light off , or change its specific operation. 1.
The operation of a specific device varies by product. The
green...
User Manual - Page 6
...removing a device from your group. Repeat steps 1-6 if this occurs. Press and hold SETUP until both the red and green LEDs blink twice. 2. When the green LED blinks ... steady blink the remote has not successfully communicated with the device. Removing a Device (Light / Node) from .
Press GROUP once. (Red LED blinks once) 4. SETTING UP AND CONTROLLING A GROUP You can set up to remove...
User Manual - Page 7
... (Device / Node) to put the remote into "GROUP Control" mode. (Red LED
blinks once) The remote will blink once.
Press SHIFT and
the digit (1-9) if you are adding devices to 32 devices per scene. 6
Deleting a Group 1. SETTING UP SCENES A scene is activated. 2. Press SCENE once. (Red LED blinks once) 4. Press and hold SETUP until both the red and green...
User Manual - Page 8
... blinks once) 4. Press DELETE once. (Red LED blinks once) 3. Press the button on the device that the remote is pending the setup of the bright/dim setting on the light you wish to the manual for the scene you are adding. (Green LED pauses briefly, blinks once and then resumes blinking rapidly, indicating that you...
User Manual - Page 9
... / Nodes) to All Control The factory default setting for the scene you have successfully deleted the device from the group. 8
CONTROLLING SCENES To control a scene, perform the following section should only be pressed.
You have pressed an invalid key or the All-On/All-Off command was not successful. Press the digit key for GE Z-Wave devices is activated...
User Manual - Page 10
...
Refer to the new secondary remote. 5. Repeat steps 1-5 if this occurs. Press and hold SETUP until both the red and green LEDs blink twice. 2.
The primary remote then copies the network and device information to the user manual for the secondary remote for instructions on "Copying Network/Device Information" if the target remote is a GE SmartHome remote. When the green LED...
User Manual - Page 11
... blink, the information has not been successfully transferred.
Refer to the primary remote, as well as receive information PRIMARY CONTROLLER SHIFT (TRANSFER) You can add a secondary remote to your network, and transfer your remote's information to another remote, so it sends its
information to the user manual for the secondary remote for more information. 5. Put the target (new primary...
User Manual - Page 12
... network information to the new primary remote. Add devices, groups, and scenes to the source (old primary) remote, as well as needed . The source remote is converted into a secondary remote and can not be used to add or delete devices from the network. 7. Refer to the user manual for the new primary remote for more information. 5.
NOTE: If...
User Manual - Page 13
... information. 6.
Reset all device and Z-Wave network information. When the green LED blinks twice, you have your remote recover network information, perform the following steps: 1. Repeat steps 1-3 if this remote. 5. Press and hold SETUP until both the red and green LEDs blink twice. 2. Add devices, groups, and scenes to clear all individual devices as instructed in the...
User Manual - Page 15
... operations could possibly result in a different room than the controlled appliance, also an unintentional activation may automatically be removed from "All" control setting. Instructions on due to timed event programming. 14 Compliance with IC Rules AND Regulations IC: 6924A-45600 Jasco Products Company Model: 45600
"Object is pressed. Z-Wave devices may occur if the wrong button on...
User Manual - Page 16
..., big screen TV, etc.) between the remote controller and the destination device, the type of construction and the number of Z-Wave enabled devices installed in metal junction boxes will suffer a significant loss of range (approximately 20-25%) since the metal box blocks a large part of the RF signal. Every Z-Wave enabled device acts as a signal repeater and...
GE 45600 Reviews
Do you have an experience with the GE 45600 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for GE yet.
Earn 750 points for your review!