Garmin Vector S Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin Vector S manuals!
Problems with Garmin Vector S?
Ask a Question
Free Garmin Vector S manuals!
Problems with Garmin Vector S?
Ask a Question
Garmin Vector S Videos
Garmin Vector S Power Meter
Duration: 1:00
Total Views: 3,815
Duration: 1:00
Total Views: 3,815
Popular Garmin Vector S Manual Pages
Owner's Manual - Page 1
Vector™ and Vector S
Owner's Manual
September 2014
Printed in Taiwan
190-01450-00_0D
Owner's Manual - Page 2
... this manual without the express permission of this product. Garmin reserves the right to change or improve its products and to www.garmin.com for a list of their respective owners. Go to make changes in part, without the written consent of Garmin. ANT +™, ANT Agent™, Garmin Connect™, USB ANT Stick™, and Vector™...
Owner's Manual - Page 3
...Setting the Installation Angle 3 Performing a Static Zero Calibration 3 Calibrating Vector Before Each Ride 3 Customizing the Data Fields 3
Training 3 Pedal-Based Power 3 Maintenance Tips 3
Vector Data 3 Sending Your Ride to Garmin Connect 3
Garmin Connect 3 Disconnecting the USB Cable 4
Device Information 4 Vector Device Care 4 Removing the Pedal Pod and Pedal 4 Replacing the Pedals...
Owner's Manual - Page 5
... pedal spindle and the
À pedal pod where it is the load-bearing connection. Improper use could result in the À
crank arm is recessed, use more than two washers. For software updates, video tutorials, and everything you must be in the product box for the Vector system. Procedures that are specific to www.garmin.com/ vectorowner for the Vector...
Owner's Manual - Page 6
... the Vector S system. 1 Apply a thin layer of the shoe.
4 Adjust the cleat to the shoe in the forward position, the pedal pod should be pointing downward.
6 Rotate the crank arm to tighten the spindle. When the crank is for clearance. Garmin® recommends placement of the pedal pod on the Edge device.
2
Introduction Installing the Left Pedal and Pedal Pod This...
Owner's Manual - Page 7
... approximately 90 rpm. Setting the Installation Angle Before you set the installation angles, you must enter the crank length, set , a message appears and data fields display power data on the Edge device (1000, 810, and 510 only). Calibrating Vector Before Each Ride For best results, Garmin recommends calibrating Vector at the start of the sensors inside the pedals, and calibrate...
Owner's Manual - Page 8
...; computer as a portable device, it can connect with Garmin parts only.
Do not use the hex nut driver to slowly loosen the pedal .
À
Á
NOTE: The spindle and crank for the Vector and Vector S systems. You should keep the left pedal parts separate from the right pedal parts.
1 Remove the pedals and pedal pods from your favorite social networking sites. Do not submerge...
Owner's Manual - Page 9
...left-handed (reverse) thread.
15Replace the pedal pods and pedals according to the installation instructions (Installing the Pedal Pod and Pedal).
16Rotate the crank arm to check for the right spindle has a left crank.
Radio frequency/ protocol
2. 4 GHz ANT + wireless communications protocol
USB ANT Stick™ Specifications
Power source
USB
Operating temperature range
From 14°...
Owner's Manual - Page 10
.... 3 Select ANT + Power > Calibrate. Edge 500 Device Instructions
Pairing Vector with the Edge 800 Device 1 Bring the Edge device within range (3 m) of the sensor.
When the sensor is paired with the Edge 800 Device 1 Enter the crank length (Entering the Crank Length). 2 Set the install angle of the sensors inside the pedals (Setting
the Installation Angle). 3 Calibrate the...
Owner's Manual - Page 11
... for the right pedal and pedal
pod (Installing the Pedal Pod and Pedal). 5 Pair the Vector system with your Garmin dealer
to www.garmin.com/ vectorowner, and download the
Vector Updater application. 2 Bring Vector within range (3 m) of power output (1 to appear.
Lap: The average left /right power balance for this data to 7) based
on - screen instructions. The scale factor...
Owner's Manual - Page 12
... fields 3, 6
E Edge 2, 5, 6
G Garmin Connect 3
H history 3
sending to computer 3
I installing 1, 2
M memory 3
P pairing 2, 5, 6 pedal pods 1, 2, 4, 5 pedals 1-4 power 3 product registration 5
R registering the device 5 replacement parts 4
S software, updating 7 specifications 5 storing data 3 storing the device 4, 5
T tools 1 training 3 troubleshooting 7
U updates, software 7 USB, disconnecting...
Garmin Vector S Reviews
We have not received any reviews for Garmin yet.