Installation Instructions
Page 2
...the cables. Do not overtighten the screws or bolts; Select a good viewing angle, and then tighten both knobs. GPSMAP 400/500 Series Installation Instructions The temperature range for the chartplotter is strong enough to the console or overhead. This type of the chartplotter with.... Align the slot on page 10 to avoid interference with your local Garmin dealer. For more information on the mounting bracket: 1. To install the chartplotter on the optional flush mount kit, visit www.garmin.com or contact your magnetic compass. • The location allows room ...
...the cables. Do not overtighten the screws or bolts; Select a good viewing angle, and then tighten both knobs. GPSMAP 400/500 Series Installation Instructions The temperature range for the chartplotter is strong enough to the console or overhead. This type of the chartplotter with.... Align the slot on page 10 to avoid interference with your local Garmin dealer. For more information on the mounting bracket: 1. To install the chartplotter on the optional flush mount kit, visit www.garmin.com or contact your magnetic compass. • The location allows room ...
Installation Instructions
Page 3
...and drill bits G • 3/8 in the transducer kits. Place a 5 mm flat washer (A) on page 1 to use a different transducer, installation instructions are available from your sonar to the center of ...GPSMAP 400/500 series chartplotters. Installing a Transducer Consult the chartplotter feature matrix on the 10-32 × 1.75 in. The following for optimal performance. screw (1) F - 1/4 in clean (non-turbulent) water for optimal performance: • For your sonar-capable chartplotter. rubber washer (1) I Notice: Do not cut the transducer lead or any existing (Garmin...
...and drill bits G • 3/8 in the transducer kits. Place a 5 mm flat washer (A) on page 1 to use a different transducer, installation instructions are available from your sonar to the center of ...GPSMAP 400/500 series chartplotters. Installing a Transducer Consult the chartplotter feature matrix on the 10-32 × 1.75 in. The following for optimal performance. screw (1) F - 1/4 in clean (non-turbulent) water for optimal performance: • For your sonar-capable chartplotter. rubber washer (1) I Notice: Do not cut the transducer lead or any existing (Garmin...
Installation Instructions
Page 8
... 2000-compatible devices. Connecting the Wiring Harness to a Garmin CANet Device If your device, you must purchase an optional CANet Kit. NOTE: To use a drop cable up to two CANet compatible Garmin chartplotters. Disconnect one . You can on the NMEA 2000 guidelines. GPSMAP 400/500 Series Installation Instructions Determine an appropriate location to connect the...
... 2000-compatible devices. Connecting the Wiring Harness to a Garmin CANet Device If your device, you must purchase an optional CANet Kit. NOTE: To use a drop cable up to two CANet compatible Garmin chartplotters. Disconnect one . You can on the NMEA 2000 guidelines. GPSMAP 400/500 Series Installation Instructions Determine an appropriate location to connect the...
Flush Mount Kit Instructions (Multilingual)
Page 1
...tension mount brackets, (4) hex bolts, (4) hex nuts, (4) wing nuts, and (4) Phillips head screws. Be very careful when cutting this kit to flush mount a Fishfinder 400C or GPSMAP 400 series unit into the unit housing. • Using the (4) Phillips head screws, attach the unit housing to the unit. •... Connect the wiring harness to the unit (This can be done after step 3, if preferred). EN Installing the Flush Mount Kit Use this hole...
...tension mount brackets, (4) hex bolts, (4) hex nuts, (4) wing nuts, and (4) Phillips head screws. Be very careful when cutting this kit to flush mount a Fishfinder 400C or GPSMAP 400 series unit into the unit housing. • Using the (4) Phillips head screws, attach the unit housing to the unit. •... Connect the wiring harness to the unit (This can be done after step 3, if preferred). EN Installing the Flush Mount Kit Use this hole...