Garmin GHP Reactor Mechanical/Retrofit/Solenoid Corepack Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin GHP Reactor Mechanical/Retrofit/Solenoid Corepack manuals!
Problems with Garmin GHP Reactor Mechanical/Retrofit/Solenoid Corepack?
Ask a Question
Free Garmin GHP Reactor Mechanical/Retrofit/Solenoid Corepack manuals!
Problems with Garmin GHP Reactor Mechanical/Retrofit/Solenoid Corepack?
Ask a Question
Popular Garmin GHP Reactor Mechanical/Retrofit/Solenoid Corepack Manual Pages
?Important Safety and Product Information - Page 2
.... Marine Warranty Policy: Certain Garmin Marine products in is still under Part 15 regulations. If these guidelines are also entitled to have a 90 day warranty. Garmin makes no guarantee that may be returned to the Garmin service center in source code form remains a valuable trade secret of intended distribution. Go to www.garmin.com/ support / warranty .html for...
Owner s Manual - Page 4
...you release the helm and manually maintain a specific heading for fishing, and it can also perform other specialty maneuvers such as Uturns and Williamson turns. There are no settings to begin a port turn... or power displacement hull boats. • Hold 1°> 10°>> or Setup > User Autopilot Setup > Direction
Control. 2 Select Enabled.
U-Turn Pattern The u-turn pattern turns ...
Owner s Manual - Page 6
... delay (from manually performing a gybe using the helm or step steering. NOTE: If you assign direction control functionality to a button on the remote, the autopilot must have a wind sensor installed. 1 Engage wind hold (page 3). 2 Select Menu > Tack/Gybe. 3 Select TACK or GYBE. Device Configuration
User Autopilot Settings
Select Menu > Setup > User Autopilot Setup.
Assigning Remote...
Installation Instructions - Page 1
GHP™ Reactor Mechanical
Installation Instructions
Important Safety Information
WARNING See the Important Safety and Product Information guide in Taiwan
190-01769-02_0B Learn to operate the autopilot on your boat.
Specific knowledge of the cables. You must know how the components operate together in accordance with all of multiple components. If needed, extension cables (sold ...
Installation Instructions - Page 2
... the setup procedure by
Garmin), a... a solenoid drive unit, a solenoid power cable...manually take control of the helm and suspends autopilot control of the GHP Reactor
Mechanical autopilot system. It detects when you may
need to be extended if needed , the alarm wires can be mounted. There must be a length of hose between a T-connector and the Shadow Drive. • In a single-helm installation...
Installation Instructions - Page 5
.... These instructions apply only to solenoid-type drive units. 1 If necessary, use the installation instructions provided with your Garmin drive unit to mount it and connect it to the ECU. 2 Route the bare-wire end of
your drive unit to identify the connections on your boat using a rudder feedback cable (sold by Garmin with the GHP Reactor Mechanical autopilot...
Installation Instructions - Page 6
... your drive unit.
4 Connect the solenoid power cable (not included) to your
sensor to the GHP Reactor Mechanical autopilot.
Installing a Garmin Rudder Feedback Sensor If you must select a mounting location (Alarm Mounting and Connection Considerations).
1 Route the alarm cable to the bare-wire end of the CCU cable.
6 Follow the installation instructions provided with 0.08 mm2 (28 AWG...
Installation Instructions - Page 8
...rudder-movement clearance to avoid damage to the farthest position that does not report an error. 1 Position the rudder so that the boat would steer fully starboard and select OK... system, you installed the autopilot on the autopilot. These settings apply only to drive units not sold by Garmin, you connected the autopilot to an existing solenoid drive
unit, select Solenoid. • ...
Installation Instructions - Page 9
... Wizard must be a problem with the speed source set to GPS. 5 If...Setup > Dealer Autopilot Setup > Compass Setup > Calibrate Compass > Begin. 2 Follow the directions on the dashboard of calm water. 2 Select Menu > Setup > Dealer Autopilot Setup...If you are performing this procedure as part of the Sea
Trial Wizard, select ...None as the speed source, Garmin recommends connecting a tachometer through...
Installation Instructions - Page 10
...procedure as part of the ...-screen instructions. 4...Setup > Fine Heading Adjustment, and adjust the fine heading setting until the autopilot performance is low, you do not have a large stretch of the Autotune procedure. Test the change before making a turn smoothly, not too quickly or too slowly. Setting the Fine Heading Adjustment This procedure appears only if you might need to manually...
Installation Instructions - Page 11
... to the default values, you must perform the Generic Tune procedure (Tuning an Existing Drive Unit). Advanced Configuration Settings You can also define each setting are not available on -screen instructions. Manually Adjusting the Settings for Dealer Autopilot Setup is satisfactory.
If you adjust any of these tuning procedures, you must perform the autotune procedure again...
Installation Instructions - Page 12
...Setup > Dealer
Autopilot Setup > Steering System Setup > Drive Unit Class. 2 Select Other or Solenoid, based on this existing drive unit if needed. After you can force the rudder to commands from +5° to -5° each time you set... system. The error tolerance of the rudder. Tuning the Speed on an Existing Drive Unit If you have a drive unit not sold by Garmin, you select ...
Installation Instructions - Page 15
...speed source. Route To maneuver. Autopilot Tuning Settings To open the speed source settings, select Menu > Setup > Dealer Autopilot Setup > Speed Source Setup. Planing RPM: Allows you to adjust the...ECU shuts
down
Error: ECU Voltage The ECU voltage has has Dropped Rapidly dropped quickly below the value specified in the low voltage alarm menu.
User-specific settings are available ...
Installation Instructions - Page 16
...These trademarks may not be correctly installed. Rudder Sensor Settings NOTE: Rudder sensor settings apply only when a rudder sensor is connected to www.garmin.com/support and click Contact Support
for in a safe
place. Calibrate Rudder Center: Initiates a procedure that establishes
the maximum range of movement of Garmin Ltd. GHP™, GHC™, Reactor™, and Shadow Drive™...
?Declaration of Conformity - Page 1
...Electrical systems. Extra-low-voltage DC installations
Manufactured by: Manufacturer's Address:
GARMIN International & 1200 E. 151st Street Olathe, Kansas 66062 U.S.A
GARMIN Corporation No.68, Zhangshu 2nd Rd..,...Equipment
Model Number(s):
GHP Reactor Mechanical
The undersigned does hereby declare that the equipment complies with the above Directives
Jamie Wiltshire Quality Supervisor Garmin ...
Garmin GHP Reactor Mechanical/Retrofit/Solenoid Corepack Reviews
We have not received any reviews for Garmin yet.