Garmin GHP Reactor Hydraulic Corepack with SmartPump Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin GHP Reactor Hydraulic Corepack with SmartPump manuals!
Problems with Garmin GHP Reactor Hydraulic Corepack with SmartPump?
Ask a Question
Free Garmin GHP Reactor Hydraulic Corepack with SmartPump manuals!
Problems with Garmin GHP Reactor Hydraulic Corepack with SmartPump?
Ask a Question
Popular Garmin GHP Reactor Hydraulic Corepack with SmartPump Manual Pages
?Important Safety and Product Information - Page 2
... product is provided by international distributors for any user-serviceable parts. Repairs have the goods repaired or replaced if the goods fail to be used with the limits for parts or labor, provided that interference will not replace missing components from Garmin warranty coverage. IN NO EVENT SHALL Garmin BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES...
Owner s Manual - Page 3
...system allows manual steering and several modes of your boat to promptly regain manual control of... set up, and customize the autopilot system.
For information about installing, see the installation instructions for... of the autopilot. Select Menu > Setup > User Autopilot Setup > Shadow Drive. "Standby" appears ...the Important Safety and Product Information guide in the product box for use...
Owner s Manual - Page 4
...hull boats. • Hold 1°> 10°>> or Setup > User Autopilot Setup > Direction
Control. 2 Select Enabled.
Williamson Turn The ...Setting Up the Zigzag Pattern You can use rudder steering mode.
The heading trend indicator appears, and the autopilot status indicator turns green to use direction control, you release the helm and manually maintain a specific...
Owner s Manual - Page 5
... wind sensor to set the autopilot to maintain a specific bearing relative to ... your autopilot. 1 Select Menu > Setup > User Autopilot Setup > Wind Hold
Type. 2 Select ... This waypoint is engaged.
CAUTION Garmin® recommends using NMEA 2000...and gybing. For advanced autopilot configuration, see the installation instructions included with the Autopilot You can use the autopilot...
Owner s Manual - Page 6
... can select a full color or high contrast color configuration. The gybe inhibitor prevents the autopilot from manually performing a gybe using the helm or step steering. Device Configuration
User Autopilot Settings
Select Menu > Setup > User Autopilot Setup. Power Mode: Sets the device power mode to normal or store demo mode.
The autopilot steers your boat through...
Owner s Manual - Page 8
.... Liberty House, Hounsdown Business Park Southampton, Hampshire, SO40 9LR UK
Garmin Corporation No. 68, Zhangshu 2nd Road, Xizhi Dist. www.garmin.com/support
913-397-8200 1-800-800-1020 +32 2 672 52 54 +49 (0)180 6 427646 00800 4412 454 +44...44 97
+43 (0) 820 220 230 + 331 55 69 33 99 + 47 815 69 555 + 46 7744 52020
Garmin International, Inc. 1200 East 151st Street
Olathe, Kansas 66062, USA...
Installation Instructions - Page 1
... of the components on your Garmin® dealer or from your boat. Extreme-temperature-induced damage and related consequences are not appropriate for product warnings and other and to each component for proper installation. GHP™ Reactor SmartPump
Installation Instructions
Important Safety Information
WARNING See the Important Safety and Product Information guide in the product box...
Installation Instructions - Page 2
... pump has five hydraulic-connector fittings, although only
three are used instead of the
SmartPump, extension cables are located within 5 m (16 ft.) of installing shutoff valves. See Pump Valves and Fittings for more than 1.5 m (5 ft.) to which you should be used with machine-crimped or field-replaceable fittings that best meets these instructions may be...
Installation Instructions - Page 4
... and the CCU must be connected to a 9 to install the pump, contact Garmin Product Support.
The alarm provides audible alerts from sources of the boat, in the hydraulic system.
4 If needed , specific connection diagrams are building a NMEA 2000 network. Hydraulic connections are not shown in this diagram. Hydraulic connections are not shown in this diagram. To extend...
Installation Instructions - Page 8
... system bleed completed successfully. Installing the Alarm Before you can install the Shadow Drive, you do not have an existing NMEA 2000 network on the helm control. 15Select an option: • If Hydraulic Pump Stall is not shown within 2 to 3
seconds after all parts, apply corrosion blocker to the instructions provided by the manufacturer of...
Installation Instructions - Page 10
... Rudder
NOTE: If an error appears during these considerations....there may have been installed correctly. Selecting the ...set the fine heading adjustment (Setting...the speed source, Garmin recommends connecting a...Setup > Dealer Autopilot Setup > Wizards
> Sea Trial Wizard. 3 If necessary, configure the planing RPM. Important Sea Trial Wizard Considerations The Sea Trial Wizard must not be a problem...
Installation Instructions - Page 11
...part of the Sea Trial Wizard, select Begin. • If you are performing this procedure outside of the Sea Trial Wizard, from the heading screen, select Menu > Setup > Dealer Autopilot Setup > Compass Setup > Fine Heading Adjustment, and adjust the fine heading setting...manually adjust the gain settings (not recommended) (Adjusting the Autopilot Gain Settings... on -screen instructions. 4 Select an...
Installation Instructions - Page 12
...screen instructions. The boat should not oscillate significantly.
2 Turn the boat in one direction with the speed source set this...set to Tach. - Running the Automated Configuration Processes Manually 1 Enable Dealer Mode (Enabling Dealer Configuration). 2 From the heading screen, select Menu > Setup > Dealer
Autopilot Setup. 3 Select an automated process:
• Select Compass Setup...
Installation Instructions - Page 15
...settings, select Menu > Setup > Dealer Autopilot Setup > Steering System Setup. If the value does not match the value on the helm control, you to set the rudder gain for 5 seconds
• The error...GPS. This setting applies when the vessel operates below planing speed.
User-specific settings are available during normal operation of the autopilot, certain settings may become overactive...
Installation Instructions - Page 16
... sensor settings, select Menu > Setup > Dealer Autopilot Setup > Steering System Setup > Rudder Sensor Setup. Port Angle: Allows you to the farthest position that does not report an error.
NMEA®, NMEA 2000®, and the NMEA 2000 logo are trademarks of Garmin Ltd. Teflon® is connected to www.garmin.com/support and click Contact Support
for in-country support information...
Garmin GHP Reactor Hydraulic Corepack with SmartPump Reviews
We have not received any reviews for Garmin yet.