Garmin GHP Reactor Steer-by-wire Standard Corepack Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin GHP Reactor Steer-by-wire Standard Corepack manuals!
Problems with Garmin GHP Reactor Steer-by-wire Standard Corepack?
Ask a Question
Free Garmin GHP Reactor Steer-by-wire Standard Corepack manuals!
Problems with Garmin GHP Reactor Steer-by-wire Standard Corepack?
Ask a Question
Popular Garmin GHP Reactor Steer-by-wire Standard Corepack Manual Pages
?Important Safety and Product Information - Page 2
... AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY. Online auction confirmations are designed to provide reasonable protection against products or services that cannot be installed and operated with the instructions. Go to www.garmin.com/ support / warranty .html for the safe and prudent operation of the vessel. You are responsible for more details and to...
?Important Safety and Product Information - Page 20
....com / aboutGarmin / environment Garmin 1999/5/EC www.garmin.com/ compliance Garmin Garmin Garmin i ii iii iv) 由于非 Garmin v) 未经 Garmin iv) 连接非 Garmin Garmin Garmin 90 90 1 Garmin Garmin Garmin Garmin RMA Garmin Garmin Garmin Garmin Garmin www.garmin.com/ support / warranty .html Garmin Marine Warranty Policy
20
?Declaration of Conformity - Page 1
...65/EU
Standard to which conformity is declared:
IEC 60945:2002 Maritime navigation and radiocommunication equipment and systems. General requirements.
Authorised Representative:
GARMIN (Europe... Navigation Equipment
Model Number(s):
GHP Reactor SBW
The undersigned does hereby declare that the equipment complies with the above Directives
Jamie Wiltshire Quality Supervisor Garmin (Europe) ...
Installation Instructions - Page 1
... • The helm control must connect to correctly plan the installation on the device. • The mounting surface must provide the correct types of the autopilot system. GHP™ Reactor Steerby-Wire
Installation Instructions
Important Safety Information
WARNING See the Important Safety and Product Information guide in the product box for registration and warranty purposes.
You...
Installation Instructions - Page 2
...instructions are building a NMEA 2000 network.
Wire... Garmin dealer or at www.garmin....specifications.
For best performance, observe these considerations when selecting a mounting location. ◦ A handheld compass should be used to test for magnetic
interference in the area where the CCU is the primary sensor of the GHP Reactor Steer...setup procedure by -
This cable should be installed...
Installation Instructions - Page 3
... Do not connect the steering controller cable to the screws before installing them. Additional instructions are mounting the helm control in the notice. 14Snap the decorative bezel into the cutout. 13Securely fasten the helm control to the helm control through the included steering controller CAN bus.
Alarm Wire Color
CCU Cable Wire Color
White (+)
Orange (+)
Black...
Installation Instructions - Page 4
...T-connectors together side-by following the instructions provided with NMEA 2000, you should...wire on the product page for the Autopilot System
NOTICE If you are installing...your boat, all the parts needed to build one...garmin.com. NOTE: The braided drain wire (bare) on the NMEA 2000 power cable must connect it through the necessary configuration steps. To download this document, select Manuals...
Installation Instructions - Page 5
...problem with the NMEA 2000 speed source or connection. This step applies only to power boats with the speed source set...Setup > Dealer Autopilot Setup > Compass Setup > Calibrate Compass > Begin. 2 Follow the directions on the helm control until calibration is available, or set to avoid damaging the steering...using None as the speed source, Garmin recommends connecting a tachometer through 3....
Installation Instructions - Page 6
...Setup > Dealer Autopilot Setup > Autopilot Tuning > Autotune > Begin. If the autopilot is connected to a GPS device that provides responsive steering. 2 Select an option:
• If you are performing this procedure as part of the Sea Trial Wizard, adjust the fine heading setting.... If the CCU is finished, follow the on-screen instructions.
4 Select an option: • If the calibration ...
Installation Instructions - Page 7
... the compass calibration procedures (Calibrating the Compass).
• Select Compass Setup > Set North to start the automatic autopilot tuning procedures (Performing the Autotune Procedure).
4 Follow the on the helm control under normal conditions.
NMEA 0183 Connection Considerations • The installation instructions provided with your NMEA 0183 device to a common ground.
Dealer Mode...
Installation Instructions - Page 8
...network (provides power to www.garmin.com/waterrating. Tx/A (+)
Ì
White -
Rx/B (-)
Ï
NMEA 0183-Compatible Device Wire Function Power NMEA 0183 ground ... device
Ã
Wire Helm Control Wire Color - Tx/A (+)
Ì
White - unconnected
Í
Brown -
Function N/A
Ê
N/A
Ë
Blue - Tx/B (-)
Í
Brown - Helm Control
Specification
Measurement
Dimensions without ...
Installation Instructions - Page 9
...Continues in Heading Hold. Rapid Update
129029 GNSS Position Data
129283 Cross-Track Error
129284 Navigation Data
129285 Navigation -
User-specific settings are available only when using ...manual provided with the CCU. NOTE: Depending upon the configuration of the autopilot. NOTE: On a powerboat, each time you change to the Speed Source setting, you can manually adjust any setting...
Installation Instructions - Page 10
...2014 Garmin Ltd. or its subsidiaries
www.garmin.com/support Low Speed: Allows you to adjust the maximum speed of Garmin Ltd. Autopilot Tuning Settings To open the speed source settings, select Menu > Setup > Dealer Autopilot Setup > Speed Source Setup. Max. Steering System Settings To open the steering system settings, select Menu > Setup > Dealer Autopilot Setup > Steering System Setup.
Garmin GHP Reactor Steer-by-wire Standard Corepack Reviews
We have not received any reviews for Garmin yet.