Garmin Reactor 40 Steer-by-wire Corepack for Volvo Penta Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin Reactor 40 Steer-by-wire Corepack for Volvo Penta manuals!
Problems with Garmin Reactor 40 Steer-by-wire Corepack for Volvo Penta?
Ask a Question
Free Garmin Reactor 40 Steer-by-wire Corepack for Volvo Penta manuals!
Problems with Garmin Reactor 40 Steer-by-wire Corepack for Volvo Penta?
Ask a Question
Popular Garmin Reactor 40 Steer-by-wire Corepack for Volvo Penta Manual Pages
Instructions - Page 1
... may not be connected to a 9-24 Vdc power source for the autopilot to the steering
system. GHP® Reactor™ Steer-by-Wire Volvo® Gateway Addendum
When installing the Garmin autopilot on your boat.
➋
Gateway data bus. LED Behavior
Description
Troubleshooting
Off
The gateway is properly receiving and transmitting data.
Flashing double-blink The gateway is...
Owners Manual - Page 5
... as you can engage the autopilot heading hold functionality, the system allows manual steering and several modes of your boat to maintain your vessel. Avoid navigational hazards and never leave the helm unattended. It does not relieve you engage and steer, set up, and customize the autopilot system. Using the helm control, you of...
Owners Manual - Page 6
...port turn .
There are 30° and 1.5 minutes. 1 Select Menu > Pattern Steering > Zigzag > Setup > Zigzag
Amplitude. 2 Select or to a person in man overboard situations. The ...set the time. 3 Select Done. CAUTION The boat must have the autopilot engaged. • Select or to begin a pattern until you release the helm and manually maintain a specific heading for use rudder steering...
Owners Manual - Page 7
... the waypoint and the location where the autopilot turns the boat 1 Select Menu > GPS Steering > Cloverleaf > Length. 2 Select or to set the autopilot to maintain a specific bearing relative to the autopilot. In addition to your autopilot. 1 Select Menu > Setup > User Autopilot Setup > Wind Hold
Type. 2 Select Apparent or True. Do not begin a port turn, select...
Owners Manual - Page 8
...installed. 1 Engage wind hold (Engaging Wind Hold, page 3). 2 Select Menu > Tack/Gybe. 3 Select Tack or Gybe. NOTE: If you assign direction control functionality to a button on the screen. System Settings
Select Menu > Setup...Response setting allows you from manually performing a gybe using the helm or step steering. Wind Limiter: Slows the rate of turn is engaged. See the instructions ...
Owners Manual - Page 9
...of navigation data and speed source periodically.
1 Select Menu > Setup > Preferred Sources > Heading Source
2 Select a source.
Using a third...Allows you to set the operating mode to be a compatible GPS compass or a magnetic heading sensor. Language: Sets the on the ... timely information, and therefore cannot often use a Garmin sensor for GPS location or speed.
Selecting the Preferred...
Installation Instructions PDF - Page 1
... registration today. You must provide the correct types of the autopilot system. You can use mounting hardware other boats. REACTOR™ 40 STEER-BYWIRE
Installation Instructions
Important Safety Information
WARNING See the Important Safety and Product Information guide in the product box for product warnings and other and to power using the included cables. For best performance...
Installation Instructions PDF - Page 3
... your device at www.garmin.com. Test any mounting hardware with 28 AWG (0.08 mm2) wire. 2 Connect the cables, based on this document, select Manuals on the NMEA 2000 power...the
steering system through a steering controller CAN bus. Additional instructions are unfamiliar with the CCU. Ensure the steering controller CAN bus is not long enough, extend the appropriate wires with the steering ...
Installation Instructions PDF - Page 4
... in your NMEA 0183 device to the input port on the wiring harness. • See Specifications, page 5 for extended runs of the approved NMEA 0183 sentences that are examples of the chartplotter owner's manual for NMEA 0183 connection information.
See the included configuration guide for the CCU to the NMEA 2000 backbone by connecting...
Installation Instructions PDF - Page 6
...Garmin Ltd.
Contacting Garmin Support • Go to heading hold
N/A
• Alarm sounds for 5 seconds
• Autopilot transitions to support.garmin.com for help and information, such as
product manuals, frequently asked questions, videos, and customer support... speed 129025 Position: Rapid update 129026 COG & SOG: Rapid update 129283 Cross track error 129284 Navigation data 129540 GNSS...
Configuration Guide PDF - Page 1
... engines, or if it must configure the autopilot system using an external GPS antenna as the speed source.
REACTOR™ 40 STEER-BYWIRE
Configuration Guide
Important Safety Information
WARNING See the Important Safety and Product Information guide in the product box for product warnings and other objects. You are used to operate the autopilot on the...
Configuration Guide PDF - Page 2
... steering. 2 Select an option: • If you are performing this procedure outside of the Sea Trial Wizard on a chartplotter, select Settings > My Vessel > Autopilot Installation Setup ...set to manually adjust the gain settings (not recommended) (Adjusting the Autopilot Gain Settings, page 3).
2 Calibrating the Compass 1 Select an option:
• If you are performing this procedure as part...
Configuration Guide PDF - Page 3
... option based on a chartplotter, select Settings > My Vessel > Autopilot Installation Setup > Compass Setup > Fine Heading Adjustment > Begin.
2 Adjust the fine heading setting until the autopilot performance is correct. If you are prompted to set north instead (Setting North, page 3). 1 Select an option:
• If you are performing this procedure as part of the Sea Trial Wizard, proceed...
Configuration Guide PDF - Page 4
....
Manually Defining Individual Configuration Settings Configuring certain configuration settings may be available after a 2018 software update. ...Setup > Dealer Autopilot Setup.
• On a chartplotter, select Settings > My Vessel > Autopilot Installation Setup.
3 Select a setting category. 4 Select a setting to constantly adjust the heading at the slightest deviation. If you set...
Configuration Guide PDF - Page 5
... to adjust the lowest RPM point of your boat. Rudder Gain Settings NOTE: If you set the rudder gain countercorrection for loose steering. On a chartplotter, select Settings > My Vessel > Autopilot Installation Setup > Rudder Gains. NOTE: These settings apply only to planing-hull powerboats with the speed source set to adjust the highest RPM point of your boat. This...
Garmin Reactor 40 Steer-by-wire Corepack for Volvo Penta Reviews
We have not received any reviews for Garmin yet.