Fujitsu MHW2060AT - Mobile 60 GB Hard Drive Support and Manuals
Get Help and Manuals for this Fujitsu item
View All Support Options Below
Free Fujitsu MHW2060AT manuals!
Problems with Fujitsu MHW2060AT?
Ask a Question
Free Fujitsu MHW2060AT manuals!
Problems with Fujitsu MHW2060AT?
Ask a Question
Popular Fujitsu MHW2060AT Manual Pages
Manual/User Guide - Page 1
... 3 Installation Conditions
3.1 Dimensions 3.2 Mounting 3.3 Cable Connections 3.4 Jumper Settings
This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. For information about handling this hard disk drive and the system installation procedure, refer to the following Integration Guide.
Manual/User Guide - Page 2
Figure 3.1 Dimensions
3-2
C141-E250 All dimensions are in mm. Installation Conditions
3.1 Dimensions
Figure 3.1 illustrates the dimensions of the disk drive and positions of the mounting screw holes.
Manual/User Guide - Page 3
... information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)."
(1) Orientation The disk drives can be 0.49N•m (5kgf...•cm). When attaching the HDD to the system frame, do not allow the system frame to touch parts (cover and base) other than parts...specification in any direction.
(2) Frame
The MR head bias of B...
Manual/User Guide - Page 4
Installation Conditions
Because of breather hole mounted to the HDD, do not allow this to block. Locating of breather
3-4
C141-E250 Figure 3.3 Location of breather hole is shown as Figure 3.3. For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting.
Manual/User Guide - Page 5
... in the cabinet such that the PCA side, in Table 3.1. 3.2 Mounting
(4) Ambient temperature
The temperature conditions for a disk drive mounted in a cabinet refer to prevent the DE surface temperature from the disk drive. The ambient temperature must satisfy the temperature conditions described in Section 1.4, and the airflow must meet the standards listed...
Manual/User Guide - Page 6
... as loud speakers. Pressing it by external magnetic fields. Installation Conditions
(5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation. Damage: Do not press the cover of the disk drive. Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which...
Manual/User Guide - Page 7
...HDD each other.
Recommended equipments
ESD Shock
Contents Wrist strap ESD mat Low shock driver
Model JX-1200-3056-8 SKY-8A (Color Seiden Mat) SS-6500
Maker SUMITOMO ...by the impact of the driver.
(2) Please observe the tightening torque of a low impact when you use an electric driver. M3 0.49N•m (5 kgf•cm).
- Installation
(1) Please use the driver of the screw strictly....
Manual/User Guide - Page 8
Connector, setting pins
PCA
Figure 3.7 Connector locations
3-8
C141-E250 Figure 3.7 shows the locations of these connectors and terminals.
Installation Conditions
3.3 Cable Connections
3.3.1 Device connector
The disk drive has the connectors and terminals listed below for connecting external devices.
Manual/User Guide - Page 9
...the cable connectors. Host system
ATA-cable
Disk Drive #0
ATA-cable
DC Power supply
Power supply cable
Disk Drive #1
Figure 3.8 Cable connections
C141-E250
Damage...44-pin type)
Model 89361-144
Manufacturer FCI
For the host interface cable, use a ribbon cable. 3.3 Cable Connections
3.3.2 Cable connector specifications
Table 3.2 lists the recommended specifications for cables carrying ...
Manual/User Guide - Page 10
Figure 3.9 Power supply connector pins (CN1)
3.4 Jumper Settings
3.4.1 Location of setting jumpers
Figure 3.10 shows the location of the power supply connector (CN1).
Figure 3.10 Jumper location
3-10
C141-E250 Installation Conditions
3.3.4 Power supply connector (CN1)
Figure 3.9 shows the pin assignment of the jumpers to select drive configuration and functions.
Manual/User Guide - Page 11
... 3.4 Jumper Settings
3.4.2 Factory default setting
Figure 3.11 shows the default setting position at the factory. Open
1
CA
2
DB
Open
(a) Master drive
1
CA
Open
Short
2
DB
(b) Slave drive
Figure 3.12 Jumper setting of master or slave drive
Note: Pins A and C should be open.
Open
Figure 3.11 Factory default setting
3.4.3 Master drive-slave drive setting
Master drive (disk drive...
Manual/User Guide - Page 12
Installation Conditions
3.4.4 CSEL setting
Figure 3.13 shows the cable select (CSEL) setting.
At this time, the CSEL of cable selection using unique interface cables. Figure 3.13 CSEL setting
Figure 3.14 and 3.15 show examples of the slave drive does not have a conductor. By connecting the CSEL of the master drive to high level. drive
drive
Figure 3.14 Example (1) of...
Manual/User Guide - Page 13
3.4 Jumper Settings
drive Figure 3.15 Example (2) of cable select
drive
3.4.5 Power up in standby setting
When pin C is grounded, the drive does not spin up at power on.
C141-E250
3-13
Fujitsu MHW2060AT Reviews
We have not received any reviews for Fujitsu yet.