Manual/User Guide
Page 42
... possible to satisfy them, contact us. The tightening torque must be 0.49N·m(5kgf·cm). if it is connected to which the HDD is zero. When attaching the HDD to the system frame, do not allow the system frame to touch parts (cover and base) other than parts to SG. Bottom... M3 screw for the mounting screw and the screw length should satisfy the specification in Figure 3.3. Installation Conditions (2) Frame The MR head bias of the HDD disk enclosure (DE) is attached. (3) Limitation of B Figure 3.3 Mounting frame structure 3-4 C141-E120-02EN
... possible to satisfy them, contact us. The tightening torque must be 0.49N·m(5kgf·cm). if it is connected to which the HDD is zero. When attaching the HDD to the system frame, do not allow the system frame to touch parts (cover and base) other than parts to SG. Bottom... M3 screw for the mounting screw and the screw length should satisfy the specification in Figure 3.3. Installation Conditions (2) Frame The MR head bias of the HDD disk enclosure (DE) is attached. (3) Limitation of B Figure 3.3 Mounting frame structure 3-4 C141-E120-02EN
Manual/User Guide
Page 43
Figure 3.4 Location of breather hole is shown as Figure 3.4. Locating of breather C141-E120-02EN 3-5 For breather hole of breather hole mounted to the HDD, do not allow this to block. 3.2 Mounting IMPORTANT Because of Figure 3.4, at least, do not allow its around φ3 to close during mounting.
Figure 3.4 Location of breather hole is shown as Figure 3.4. Locating of breather C141-E120-02EN 3-5 For breather hole of breather hole mounted to the HDD, do not allow this to block. 3.2 Mounting IMPORTANT Because of Figure 3.4, at least, do not allow its around φ3 to close during mounting.
Manual/User Guide
Page 45
...Handling cautions Please keep the following cautions, and handle the HDD under the safety environment. Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. C141-E120-02EN 3-7 Pressing it by external magnetic ...fields. Damage: Do not press the cover of the disk drive. Mounting screw hole Cable connection Mounting ...
...Handling cautions Please keep the following cautions, and handle the HDD under the safety environment. Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. C141-E120-02EN 3-7 Pressing it by external magnetic ...fields. Damage: Do not press the cover of the disk drive. Mounting screw hole Cable connection Mounting ...
Manual/User Guide
Page 46
HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when you use an electric driver. Recommended equipments ... driver of the screw strictly. Do not drop. M3 0.49 N·m (5 Kg·cm) - Installation Conditions - Do not place HDD vertically to avoid falling down. Figure 3.7 Handling cautions - Do not hit HDD each other. ESD mat Shock absorbing mat Place the shock absorbing mat on the operation table, and place ESD mat...
HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when you use an electric driver. Recommended equipments ... driver of the screw strictly. Do not drop. M3 0.49 N·m (5 Kg·cm) - Installation Conditions - Do not place HDD vertically to avoid falling down. Figure 3.7 Handling cautions - Do not hit HDD each other. ESD mat Shock absorbing mat Place the shock absorbing mat on the operation table, and place ESD mat...
Manual/User Guide
Page 229
... DH DRDY DRQ DSC DWF dB A-scale weighting Disk enclosure Device/head register Drive ready Ddata request bit Drive seek complete Drive write fault E ECC Error checking and correction ER Error register ERR Error F FR Feature register H HA Host adapter HDD Hard disk drive I IDNF ID not found IRQ14 Interrupt request 14 L LED Light emitting diode...
... DH DRDY DRQ DSC DWF dB A-scale weighting Disk enclosure Device/head register Drive ready Ddata request bit Drive seek complete Drive write fault E ECC Error checking and correction ER Error register ERR Error F FR Feature register H HA Host adapter HDD Hard disk drive I IDNF ID not found IRQ14 Interrupt request 14 L LED Light emitting diode...