Instruction Manual
Page 7
... button D. E D A. Mode selection dial C. Side handle H. Handle shocks INTENDED USE C These heavy duty rotary and chipping hammers are factory tested; beats per minute SAVE THESE INSTRUCTIONS FOR FUTURE USE F FIG. 1 G Motor Be sure your power supply ... minute sfpm .....surface feet per minute RPM ........ Chuck B. Depth rod release button J. impacts per minute IPM.......... DEWALT tools are designed for professional concrete drilling and chiseling applications. Depth rod (only D25413 & D25416) I English .../min ..... per minute BPM ........ if this...
... button D. E D A. Mode selection dial C. Side handle H. Handle shocks INTENDED USE C These heavy duty rotary and chipping hammers are factory tested; beats per minute SAVE THESE INSTRUCTIONS FOR FUTURE USE F FIG. 1 G Motor Be sure your power supply ... minute sfpm .....surface feet per minute RPM ........ Chuck B. Depth rod release button J. impacts per minute IPM.......... DEWALT tools are designed for professional concrete drilling and chiseling applications. Depth rod (only D25413 & D25416) I English .../min ..... per minute BPM ........ if this...
Instruction Manual
Page 8
...SIDE HANDLE 1. NOTE: Use lower speeds for starting holes without a center punch, drilling in the side handle slipping during tool operation and subsequent loss of the rotary hammer. Failure to do so may result. Use drill-only mode for wood, metal, and plastics. English These heavy duty rotary... hammers are better for drilling in wood and composition board and for using abrasive and polishing...
...SIDE HANDLE 1. NOTE: Use lower speeds for starting holes without a center punch, drilling in the side handle slipping during tool operation and subsequent loss of the rotary hammer. Failure to do so may result. Use drill-only mode for wood, metal, and plastics. English These heavy duty rotary... hammers are better for drilling in wood and composition board and for using abrasive and polishing...
Instruction Manual
Page 9
... The red indicator LED (J) lights up can cause injury. English HAMMERDRILL MODE To use proper hand position as shown. Use this mode for masonry drilling. E-Clutch and Indicator Light (Fig. 4) (D25416 ONLY) The e-clutch offers increased user FIG. 4 comfort and safety through an on the side... as shown. Push and rotate bit until it from power source before installing and removing accessories, before adjusting or when making repairs. HAMMER-ONLY MODE For light chiseling, press the mode selector button (H) and turn the mode selection dial (G) so the yellow arrow points ...
... The red indicator LED (J) lights up can cause injury. English HAMMERDRILL MODE To use proper hand position as shown. Use this mode for masonry drilling. E-Clutch and Indicator Light (Fig. 4) (D25416 ONLY) The e-clutch offers increased user FIG. 4 comfort and safety through an on the side... as shown. Push and rotate bit until it from power source before installing and removing accessories, before adjusting or when making repairs. HAMMER-ONLY MODE For light chiseling, press the mode selector button (H) and turn the mode selection dial (G) so the yellow arrow points ...
Instruction Manual
Page 10
...FIG. 6 C E D D Depth Rod (Fig. 6) (ONLY FOR D25413 & D25416) TO ADJUST THE DEPTH ROD 1. To reverse the rotary hammer, turn the rotary hammer off and position the reversing lever (H) to the left. To position the lever for forward operation, turn it off and push the reversing lever (H) to... the right. Release the button to reverse the rotary hammer for strong reactive torque. FIG. 7 H 8 Push in drill-only mode. When drilling with the depth rod, stop when end of rod reaches surface of the bit equals the desired...
...FIG. 6 C E D D Depth Rod (Fig. 6) (ONLY FOR D25413 & D25416) TO ADJUST THE DEPTH ROD 1. To reverse the rotary hammer, turn the rotary hammer off and position the reversing lever (H) to the left. To position the lever for forward operation, turn it off and push the reversing lever (H) to... the right. Release the button to reverse the rotary hammer for strong reactive torque. FIG. 7 H 8 Push in drill-only mode. When drilling with the depth rod, stop when end of rod reaches surface of the bit equals the desired...
Instruction Manual
Page 11
... hole [5/32" to 3/16" (3,8 mm to 5 mm] is no need to center punch the point to keep drill biting, but do not push hard enough to full power while applying firm pressure on the hammer to be backed up " block to prevent damage to control the twisting action and avoid injury. 6. Use...
... hole [5/32" to 3/16" (3,8 mm to 5 mm] is no need to center punch the point to keep drill biting, but do not push hard enough to full power while applying firm pressure on the hammer to be backed up " block to prevent damage to control the twisting action and avoid injury. 6. Use...
Instruction Manual
Page 12
...-433-9258) or visit our website: www. If you need assistance in these parts. English 2. When drilling deep holes, if the hammer speed starts to lock it by DEWALT, have not been tested with water and mild soap. This prevents serious damage to 25 mm) Concrete No-load BPM 0-4,700 10 MAXIMUM RECOMMENDED...
...-433-9258) or visit our website: www. If you need assistance in these parts. English 2. When drilling deep holes, if the hammer speed starts to lock it by DEWALT, have not been tested with water and mild soap. This prevents serious damage to 25 mm) Concrete No-load BPM 0-4,700 10 MAXIMUM RECOMMENDED...