Dewalt DW325C Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DW325C manuals!
Problems with Dewalt DW325C?
Ask a Question
Free Dewalt DW325C manuals!
Problems with Dewalt DW325C?
Ask a Question
Popular Dewalt DW325C Manual Pages
Instruction Manual - Page 3
....
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DeWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DeWALT (1-800-433-9258)
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
Important Safety Instructions
WARNING: Do not operate this unit until you read the manual and pay attention to a compressor rated at over 200 psi...
Instruction Manual - Page 4
...Fig. The
tool driving mechanism may result. (Fig. Leaking air, damaged parts
or missing parts should be repaired or
replaced before use
combustible gases or any other reactive
gas as a power source for...remove
magazine, perform maintenance or clear jammed fasteners
while connected to the air supply and nails are not for free movement of trigger and contact
trip. I )
• ...
Instruction Manual - Page 5
... that nails are set into open air, concrete, stone, extremely hard woods, knots or any debris and be locked in a clean, FIG. Using the trigger lock-off will prevent accidental discharge.
• Do not overreach. Make sure the pressure in elevated environments such as a hammer. M)
• Refer to the Maintenance and Repairs sections...
Instruction Manual - Page 6
...
of FIG. R)
• Keep face and body parts away from tool recoil.
U trigger, do not actuate...manual for triggering options. FIG. CONTACT ACTION TRIGGER
FIG. U)
• Stay alert, watch what you are
doing and use tool while tired or under
the influence of FIG.
Hold workpiece with a strong force.
• Allow the tool to the body, especially when nailing...
Instruction Manual - Page 7
... determine the amount of air required. To reduce your fastener usage averages 50 nails per minute. Everyday eyeglasses are specially designed to filter out microscopic particles. WARNING: ALWAYS USE SAFETY GLASSES. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
Specifications
MODEL
DW325C
HEIGHT
13-1/4" (336 mm)
WIDTH
5-9/16" (140 mm)
LENGTH
12-1/16" (306 mm...
Instruction Manual - Page 8
... is not available, add 5 to Tool Specifications. 7. Always wear eye and ear protection when operating this manual. Lubricate the tool following procedures and checks before each use of use detergent oil or additives as they will
damage o-rings and rubber parts.
Check air supply. English
FIG. 1 B
a. Use DeWALT pneumatic tool oil or a non-detergent...
Instruction Manual - Page 9
... but not touching the work surface to hold the tool with finger on framing, toe nailing and crating applications.
SEQUENTIAL TRIP (GRAY TRIGGER) The Sequential Trip requires the operator to.../CSA Z94.3)] and hearing protection [ANSI S12.6 (S3.19)] when operating this series tool. DeWALT offers two types of operation for the operator to recontact the work surface with a contact trip tool...
Instruction Manual - Page 11
... the canister bracket (J) are in slot on the feed pawl (L).
Load the coil of the canister. To change setting: a. Release the canister latch (H) on the nose). The nail heads fit in the slot on the rear of nails, refer to Tool Specifications to left until tabs
disengage. Always drain the compressor tanks at temperatures below...
Instruction Manual - Page 12
... identical replacement parts.
10 To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should operate normally. Turn pressure up to operating level (not to drain from hoses
ACTION WHY HOW
ACTION WHY HOW
Clean magazine, pusher, and contact trip mechanism Permits smooth operation, reduces wear, and prevents jams Blow clean with DeWALT Pneumatic...
Instruction Manual - Page 13
... reason, you in the unlikely event a safety notification is a problem with your tool are not completely satisfied with the performance of your product will maintain the tool and replace worn parts caused by others. Seven Year Limited Warranty
DeWALT will serve as o-rings and driver blades, are not covered.
90 DAY MONEY BACK GUARANTEE If...
Instruction Manual - Page 14
... bumper
Replace bumper
Loose cap screws
Tighten and recheck
Failure to cycle
Air supply restriction
Check air supply equipment
Tool dry, lack of serious personal injury, remove
fasteners from magazine before making any adjustments or servicing this tool. FOR MORE SERIOUS OR PERSISTENT PROBLEMS, CONTACT A DeWALT SERVICE CENTER OR CALL 1-(800)-4-DeWALT.
English
TROUBLESHOOTING GUIDE...
Instruction Manual - Page 15
English
TROUBLESHOOTING GUIDE
MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW.
intermittent Worn bumper
Replace bumper
feed
Tar/dirt in driver channel
Disassemble and clean nose and driver
Air restriction/inadequate air flow through quick Replace quick disconnect fittings
disconnect socket and plug
Worn piston O-ring
Replace O-ring, check driver
Tool dry, ...
Instruction Manual - Page 16
... bottom not set correctly
Set canister bottom for length of nails being used
Broken weld wires in nail coil
Remove coil of nails and use another coil
Wrong slide plate adjustment for
Adjust switch pins for wire/plastic collated
wire/plastic collated nail coil
nail coil
14 FOR MORE SERIOUS OR PERSISTENT PROBLEMS, CONTACT A DeWALT SERVICE CENTER OR CALL 1-(800)-4-DeWALT.
WARNING: To...
Parts Diagram - Page 3
Partslist,pricing,andavailabilitysubjecttochange.Pleasevisitwww.dewaltservicenet.comfor DW325C Type 1
Description
QtyRequired
N70157
BUMPER-B
1
N80354
GASKET-NOSE
1
N80130
DRIVERGUIDE
1
N80158
NOSE
1
N80119
PAWL-FEED
1
N50087
PIN-SPECIAL(STEP)
1
N80120
SPRING-TORSION
1
854004
WASHER-RUBBER-7
3
MRG009824
O-RING-.386X.094
1
851384
O-RING-.987X.103
1
...
Parts Diagram - Page 4
Page3
Partslist,pricing,andavailabilitysubjecttochange.Pleasevisitwww.dewaltservicenet.comfor DW325C Type 1
Description
QtyRequired
BUSHING-RUBBER
1
SPACER-FRAME
1
BOTTOM-CANISTER
1
PIN-SPIROL1/4X17
1
ARM-CONTACT-SERRATED
1
SPRING-CONTACTARM
1
WASHER-1/4HICOLLO
1
SCREW-SHCS-M6X1.00X1
1
GUARD-CONTACTARM
1
ROD-FEEDPISTON
1
DW325CLABEL
2
WARNING...
Dewalt DW325C Reviews
We have not received any reviews for Dewalt yet.