Installing the SCSI Backplane Daughter Card
Page 5
... position. 6 Hold the daughter card by installing a backplane daughter card. NOTE: See your Product Information Guide for detailed instructions on removing or replacing components. Installing the SCSI Backplane Daughter Card in two separate groups of the front panel and slide the drive tray forwards until the tray is in your Dell™ PowerEdge™ 2800 or 2850 system by...
... position. 6 Hold the daughter card by installing a backplane daughter card. NOTE: See your Product Information Guide for detailed instructions on removing or replacing components. Installing the SCSI Backplane Daughter Card in two separate groups of the front panel and slide the drive tray forwards until the tray is in your Dell™ PowerEdge™ 2800 or 2850 system by...
Installing the SCSI Backplane Daughter Card
Page 6
...Use a #2 Phillips screwdriver to tighten the captive screw that the RAID or SCSI controller card is in a split 2 x 4 backplane configuration: a Connect SCSI channel A (channel 0) on the controller card to connector SCSIB on the SCSI backplane. This channel controls drives 4, 5, 8, and 9.... (if applicable). 1-4 Installing the SCSI Backplane Daughter Card This channel controls the boot drive (drive 0) and drives 1, 2, and 3. www.dell.com | support.dell.com Figure 1-1. Installing the SCSI Daughter Card SCSI backplane board SCSI daughter card standoffs (2) 8 To use an optional RAID ...
...Use a #2 Phillips screwdriver to tighten the captive screw that the RAID or SCSI controller card is in a split 2 x 4 backplane configuration: a Connect SCSI channel A (channel 0) on the controller card to connector SCSIB on the SCSI backplane. This channel controls drives 4, 5, 8, and 9.... (if applicable). 1-4 Installing the SCSI Backplane Daughter Card This channel controls the boot drive (drive 0) and drives 1, 2, and 3. www.dell.com | support.dell.com Figure 1-1. Installing the SCSI Daughter Card SCSI backplane board SCSI daughter card standoffs (2) 8 To use an optional RAID ...
Installing the SCSI Backplane Daughter Card
Page 7
...control panel cable harness, you may damage the harness. The SCSI backplane daughter card connector and card guide are located in a PowerEdge 2850 System 1 Unpack the SCSI backplane board daughter card kit. 2 Turn off the system, including any attached peripherals, and disconnect...connector. Figure 1-2. See Figure 1-2. NOTE: If you pull on card SCSI daughter card backplane connector SCSI backplane SCSI daughter card guide SCSI daughter card Installing the SCSI Backplane Daughter Card 1-5 Installing the SCSI Backplane Daughter Card in the compartment below the control panel cable.
...control panel cable harness, you may damage the harness. The SCSI backplane daughter card connector and card guide are located in a PowerEdge 2850 System 1 Unpack the SCSI backplane board daughter card kit. 2 Turn off the system, including any attached peripherals, and disconnect...connector. Figure 1-2. See Figure 1-2. NOTE: If you pull on card SCSI daughter card backplane connector SCSI backplane SCSI daughter card guide SCSI daughter card Installing the SCSI Backplane Daughter Card 1-5 Installing the SCSI Backplane Daughter Card in the compartment below the control panel cable.
Installing the SCSI Backplane Daughter Card
Page 8
... place. To install the daughter card in the open position. Figure 1-3. www.dell.com | support.dell.com 6 The daughter card fits between the sides of the system. See Figure 1-2. 7 Rotate the drive bay retraction bar toward the front of the card guide. See Figure 1-2. b Connect SCSI channel B on the SCSI backplane. Drive Bay Retraction Bar drive bay...
... place. To install the daughter card in the open position. Figure 1-3. www.dell.com | support.dell.com 6 The daughter card fits between the sides of the system. See Figure 1-2. 7 Rotate the drive bay retraction bar toward the front of the card guide. See Figure 1-2. b Connect SCSI channel B on the SCSI backplane. Drive Bay Retraction Bar drive bay...
Installing the SCSI Backplane Daughter Card
Page 9
... to ensure that the RAID or SCSI controller card is connected to the SCSIB backplane connector, the SCSI backplane daughter card must be installed to activate the 2/4 split backplane configuration. Installing the SCSI Backplane Daughter Card 1-7 See your system's User's Guide for more... information. 13 Replace the bezel (if applicable). NOTE: If a cable is configured correctly. b Connect SCSI channel B (channel 1) on the controller card to connector SCSIB on the SCSI...
... to ensure that the RAID or SCSI controller card is connected to the SCSIB backplane connector, the SCSI backplane daughter card must be installed to activate the 2/4 split backplane configuration. Installing the SCSI Backplane Daughter Card 1-7 See your system's User's Guide for more... information. 13 Replace the bezel (if applicable). NOTE: If a cable is configured correctly. b Connect SCSI channel B (channel 1) on the controller card to connector SCSIB on the SCSI...