Release Notes
Page 5
By default, the module will function according to either role (Ethernet or Stacking). In ...required for the change to take effect. ¾ Custom Protocol Based VLANs Prior to the 3.2 release only ARP, IP and IPX are supported. When the management unit fails, only the management switch needs to be restarted. ¾ ...Since this feature, VLAN names must be configured to its module ID. This feature is called non-stop forwarding. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes Added Functionality in this Release ¾ Non-Stop Forwarding This feature creates an option to ...
By default, the module will function according to either role (Ethernet or Stacking). In ...required for the change to take effect. ¾ Custom Protocol Based VLANs Prior to the 3.2 release only ARP, IP and IPX are supported. When the management unit fails, only the management switch needs to be restarted. ¾ ...Since this feature, VLAN names must be configured to its module ID. This feature is called non-stop forwarding. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes Added Functionality in this Release ¾ Non-Stop Forwarding This feature creates an option to ...
Release Notes
Page 7
... now called the Multicast Group Membership Discovery (MGMD) Proxy. This feature is enabled by default if using phones with CDP enabled, but should be disabled if a Voice VLAN is ... Version 3.2.0.6 Page 5 The miscreant sends ARP requests or responses mapping another station's IP address to its unsuspecting neighbors. This value is retrieved by LLDP when the LLDPDU is... used to share information between neighboring devices (routers, bridges, access servers, and switches). PowerConnect 6224/6224F/6224P/6248/6248P Release Notes ¾ MLD Snooping (RFC2710) In IPv4, Layer 2 switches ...
... now called the Multicast Group Membership Discovery (MGMD) Proxy. This feature is enabled by default if using phones with CDP enabled, but should be disabled if a Voice VLAN is ... Version 3.2.0.6 Page 5 The miscreant sends ARP requests or responses mapping another station's IP address to its unsuspecting neighbors. This value is retrieved by LLDP when the LLDPDU is... used to share information between neighboring devices (routers, bridges, access servers, and switches). PowerConnect 6224/6224F/6224P/6248/6248P Release Notes ¾ MLD Snooping (RFC2710) In IPv4, Layer 2 switches ...
Release Notes
Page 9
This can be done for the following reasons: • Prevent a routing loop in the network (default route configured on a router). • A preventive measure against a DOS attack on a router with unwanted destination ... A ping can be initiated via SNMP using the MIB defined in RFC 2925. System Firmware Version 3.2.0.6 Page 7 PowerConnect 6224/6224F/6224P/6248/6248P Release Notes ¾ Ping/Traceroute Enhancements New ping options have been added to allow the user to specify... the physical network is not on point-to-point interfaces even if the source IP address is a broadcast network.
This can be done for the following reasons: • Prevent a routing loop in the network (default route configured on a router). • A preventive measure against a DOS attack on a router with unwanted destination ... A ping can be initiated via SNMP using the MIB defined in RFC 2925. System Firmware Version 3.2.0.6 Page 7 PowerConnect 6224/6224F/6224P/6248/6248P Release Notes ¾ Ping/Traceroute Enhancements New ping options have been added to allow the user to specify... the physical network is not on point-to-point interfaces even if the source IP address is a broadcast network.
Release Notes
Page 15
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes ¾ Trap Configuration In previous ...commands are preserved for controlling traps was increased from the show users login-history commands have changed to ip mroute. Subnet based VLAN limit was only configurable. ¾ GARP Leave Timer The valid range for ...multicast route has changed to 20-600 centiseconds. ¾ IP Multicast Static Route Configuration The command for configuring all trap flags. The ip multicast staticroute command is enabled by default. If your previous configuration had flow control disabled, you ...
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes ¾ Trap Configuration In previous ...commands are preserved for controlling traps was increased from the show users login-history commands have changed to ip mroute. Subnet based VLAN limit was only configurable. ¾ GARP Leave Timer The valid range for ...multicast route has changed to 20-600 centiseconds. ¾ IP Multicast Static Route Configuration The command for configuring all trap flags. The ip multicast staticroute command is enabled by default. If your previous configuration had flow control disabled, you ...
Release Notes
Page 23
...the restart interval in the RFC 4750 MIB. Use this command to its default. • ietf - Default: Not applicable This command is a result of the initiate failover command). Use this command to show ip ospf Description Use this command to revert the grace period to enable OSPF graceful... of the check pointing process. Default: Not applicable Use this command to enable non-stop forwarding is not enabled on a VLAN. Use the "no" form of this command to configure the length of the grace period on a VLAN. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes CLI Reference...
...the restart interval in the RFC 4750 MIB. Use this command to its default. • ietf - Default: Not applicable This command is a result of the initiate failover command). Use this command to show ip ospf Description Use this command to revert the grace period to enable OSPF graceful... of the check pointing process. Default: Not applicable Use this command to enable non-stop forwarding is not enabled on a VLAN. Use the "no" form of this command to configure the length of the grace period on a VLAN. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes CLI Reference...
Release Notes
Page 31
...IP Map Description ip default gateway and ip default route are for different types of interfaces. ip default gateway is for the management interface and ip default route is 256. User Impact The maximum number of MAC-based VLANs is for VLAN routing interfaces. User Impact Ensure the correct command is a known limitation of the PowerConnect... 3.2.0.6 Page 29 User Impact This behavior is used for the interface being configured. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes LACP Description LAGs Supported VLAN Description vlan association mac command limitations...
...IP Map Description ip default gateway and ip default route are for different types of interfaces. ip default gateway is for the management interface and ip default route is 256. User Impact The maximum number of MAC-based VLANs is for VLAN routing interfaces. User Impact Ensure the correct command is a known limitation of the PowerConnect... 3.2.0.6 Page 29 User Impact This behavior is used for the interface being configured. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes LACP Description LAGs Supported VLAN Description vlan association mac command limitations...