User Manual
Page 21
...Indicates that no action should be taken. (This is the default.) - Example Console(config)#interface ethernet 1/5 Console(config-if)#port security action shutdown Console(config-if)#port security Console(config-if)# Switch 5224: Port Security The Ports/Port Security page contains links to the following pages: • Global... is detected. To save any changes you do not want to configure: • Shutdown and Trap - Addendum to all ports on the switch. None: Indicates that the port should be disabled and an SNMP trap message sent. This setting applies to the 3 248 and 52 24...
...Indicates that no action should be taken. (This is the default.) - Example Console(config)#interface ethernet 1/5 Console(config-if)#port security action shutdown Console(config-if)#port security Console(config-if)# Switch 5224: Port Security The Ports/Port Security page contains links to the following pages: • Global... is detected. To save any changes you do not want to configure: • Shutdown and Trap - Addendum to all ports on the switch. None: Indicates that the port should be disabled and an SNMP trap message sent. This setting applies to the 3 248 and 52 24...
User Manual
Page 24
... link goes down. RSTP achieves much faster reconfiguration (around one route exists between switches, bridges or routers. The switch supports the following STPs: • STP - Example Console(config)#interface ethernet 1/5 Console(config-if)#port security action trap-andshutdown Console(config-if)#port security ...to detect and disable network loops, and to changes in your network such as a general replacement for all switch ports. www.dell.com | support.dell.com Command port security action {trapand-shutdown} Usage Configures the port security action for the slower, legacy STP....
... link goes down. RSTP achieves much faster reconfiguration (around one route exists between switches, bridges or routers. The switch supports the following STPs: • STP - Example Console(config)#interface ethernet 1/5 Console(config-if)#port security action trap-andshutdown Console(config-if)#port security ...to detect and disable network loops, and to changes in your network such as a general replacement for all switch ports. www.dell.com | support.dell.com Command port security action {trapand-shutdown} Usage Configures the port security action for the slower, legacy STP....
User Manual
Page 32
...: 128.) • Path Cost - Defines the priority used by the STP to the 32 48 and 5 224 User 's Guides trunk: 500,000 Fast Ethernet - half duplex: 200,000; The priority and MAC address of the Spanning Tree. • Designated Port - Path cost takes precedence over port priority. - This ...is enabled. (Range: 0-240, in the Spanning Tree. The priority and number of the port on a switch is the same, the port with the root of 16; full duplex: 1,000,000; www.dell.com | support.dell.com - trunk: 5,000 NOTICE: When the Path Cost Method is set to short, the maximum path cost...
...: 128.) • Path Cost - Defines the priority used by the STP to the 32 48 and 5 224 User 's Guides trunk: 500,000 Fast Ethernet - half duplex: 200,000; The priority and MAC address of the Spanning Tree. • Designated Port - Path cost takes precedence over port priority. - This ...is enabled. (Range: 0-240, in the Spanning Tree. The priority and number of the port on a switch is the same, the port with the root of 16; full duplex: 1,000,000; www.dell.com | support.dell.com - trunk: 5,000 NOTICE: When the Path Cost Method is set to short, the maximum path cost...
User Manual
Page 35
...IP address and a subnet mask that are allowed access to the switch using the Web interface or Telnet. IP addresses that are permitted SNMP access are available: • IP Filter List - Example Console(config)#interface ethernet 1/5 Console(config-if)#spanning-tree port-priority 128 Console(config-if...19 Console(config-if)#spanning-tree link-type auto Console(config-if)#no spanning-tree edge-port Console#spanning-tree protocol-migration ethernet 1/5 Simple Network Management Protocol The Simple Network Management Protocol (SNMP) page contains a new link to the following options are specified by...
...IP address and a subnet mask that are allowed access to the switch using the Web interface or Telnet. IP addresses that are permitted SNMP access are available: • IP Filter List - Example Console(config)#interface ethernet 1/5 Console(config-if)#spanning-tree port-priority 128 Console(config-if...19 Console(config-if)#spanning-tree link-type auto Console(config-if)#no spanning-tree edge-port Console#spanning-tree protocol-migration ethernet 1/5 Simple Network Management Protocol The Simple Network Management Protocol (SNMP) page contains a new link to the following options are specified by...